LG CodeZero A9 Series Скачать руководство пользователя страница 82

Страница: 82 / 104

-82-

Only training and service purposes

Yes

Failures and measures

1. Charging failure (1/2)

Check Point

Checkpoints

The battery is normal.

Measures

Check if the

battery is faulty

(Product body/

Auxiliary).

Check the

charging

terminal for

foreign objects

Is the normal signal (00)

displayed when the battery

is attached to the test jig?

Is there any foreign object

on the charging terminal of

the charging station and/or

the product body?

No foreign objects on the

charging terminal - Move to

“3. Charging failure (2/2)“

Replace the

battery.

Try again after

removing foreign

objects from the

charging terminal

* Check the failure table attached to the right side of

the jig for detailed failure codes and symptoms.

1) Connect the battery.

2) Select A9-K (Battery test -

Green

3) Press START.

Содержание CodeZero A9 Series



































































Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды

LG CodeZero A9 Series, Руководство по обслуживанию

Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды