LG CodeZero A9 Series Скачать руководство пользователя страница 28

Страница: 28 / 104

-28-

Only training and service purposes

How to Disassemble, Reassemble and Repair Main Parts

4. How to Replace the Motor Assembly

(1) Disassemble the decor

part using a flat-head

screwdriver. (The part

needs to be replaced if

damaged during

assembly)

(2) Hold the pipe part and

pull.

(3) Loosen the screw at the

bottom of the pipe.

(4) Hold the pipe part and

pull.

(5) Remove the connector

and gasket.

(6) Remove the filter cover

and filter by hand.

(7) Disassemble three

screws from the air

guide.

(8) Remove the product

body, gasket and

harness.

(9) Remove the motor

located in the product

body.

(10) Reassemble following

the reverse order of

disassembly.

※

Note

If the gasket is damaged when replacing

the motor, replace it with insulating tape as

shown in the photograph.

Содержание CodeZero A9 Series



































































Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды

LG CodeZero A9 Series, Руководство по обслуживанию

Результаты поиска

Содержание CodeZero A9 Series

Отзывы:

Похожие инструкции для CodeZero A9 Series

Бренды по названию

Популярные бренды