LG CodePlus HCS6300 Series Скачать руководство пользователя

Страница: 43 / 52

206-4122

Configuration Options via Command Line (Cont.)

Access the Satellite Receiver Menu for the Selected Transcoder

See “Satellite Receiver Menu Commands” on pages 44 to 47 for detailed information on

satellite STB configuration options.

Update Firmware on the Selected Transcoder

This command updates the firmware on the selected transcoder card. To update firmware on

all transcoders or on the HCS6300, see “Update HCS6300 and/or Transcoder Firmware” on

page 36.

Caution: Do NOT initiate simultaneous menu sessions while a firmware update is

in progress. Doing so will interfere with the active processes and may corrupt the

system configuration and/or cause the HCS6300 card to cease normal operation.

If you are not sure of the current firmware version, view and record the transcoder hardware

ID (firmware version) before you initiate the firmware update. See “View Hardware

Information for the Selected Transcoder” on page 41.
1. Confirm the directory location of the required firmware update configuration (.cfg) and

package (.pkg) files.

Note: For a TFTP file transfer, the firmware update files must be

available on the same machine as the TFTP server.

2. At the

[

Card

(

)] Command >

prompt, type

upd

and press

Enter

3. At the

Use TFTP to transfer files (y/n)?

prompt, either:

• Type

and press

Enter

to use TFTP for the firmware update.

• Type

and press

Enter

if you will not use TFTP for the firmware update. At the next

system prompt:

Use XMODEM to transfer files (y/n)?

, type

and press

Enter

4. Complete the update using the selected transfer mode (Xmodem or TFTP). Refer to

“Update HCS6300 and/or Transcoder Firmware” on page 36 for further information.

5. Reset the transcoder card (see “Reset the Selected Transcoder Card” below).

Reset the Selected Transcoder Card

At the

[

Card

(

)] Command >

prompt, type

irst

and press

Enter

to initiate the reset. After

reset, the transcoder card resumes normal operation.

Return to the HCS6300 Main Menu

At the

[

Card

(

)] Command >

prompt, type

ret

and press

Enter

to return to the HCS6300

Main Menu.

Содержание CodePlus HCS6300 Series




















































Результаты поиска

Содержание CodePlus HCS6300 Series

Отзывы:

Похожие инструкции для CodePlus HCS6300 Series

Бренды по названию

Популярные бренды

LG CodePlus HCS6300 Series, Инструкция по установке и настройке, гарантия

Результаты поиска

Содержание CodePlus HCS6300 Series

Отзывы:

Похожие инструкции для CodePlus HCS6300 Series

Бренды по названию

Популярные бренды