LG ASBCNA0 Скачать руководство пользователя страница 19

Страница: 19 / 122

rights reserved. Only training and service purposes.

- 19 -

3-24

HOW TO REMOVE AND REINSTALL THE HOMEBAR

3-24-1 CASE ASSEMBLY, HOME BAR

The Home Bar is removable for easy cleaning and

adjustment.

1. To remove the Home Bar, Slopingly lifts the Home Bar

up and pulls straight out.

2. To replace the Home Bar, Slopingly slides it in above

the desired support and push down until it snaps into

place.

NOTE

: Some Home Bar may vary in appearance and

will only fit in one location.

3-24-3 DOOR BASKET OF HOME BAR

The Door Baskets of Homebar are removable for easy cleaning and adjustment.

1. To remove the Door Baskets of Homebar, simply lifts the Door Baskets of Homebar up and pulls straight out.

2. To replace the Door Baskets of Homebar, slides it in above the desired support and push down until it snaps into

place.

NOTE

: Some Door Baskets of Homebar may vary in appearance and will only fit in one location.

Содержание ASBCNA0


















































































































Результаты поиска

Содержание ASBCNA0

Отзывы:

Похожие инструкции для ASBCNA0

Бренды по названию

Популярные бренды

LG ASBCNA0, Руководство по обслуживанию

Результаты поиска

Содержание ASBCNA0

Отзывы:

Похожие инструкции для ASBCNA0

Бренды по названию

Популярные бренды