LG ARNU073 B3G4 Скачать руководство пользователя страница 41

Страница: 41 / 80

Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

REFRIGERANT PIPING

Tightening Flare Nuts

When connecting the flare nuts, coat the flare (inside and outside) with polyvinyl ether (PVE) refrigeration oil only.

Note:

•

Do not use polyolyester (POE) or any other type of mineral oil as a lubricant. These lubricants are not compat-

ible with PVE oil used in this system and create oil sludge leading to equipment damage and system malfunction..

Initially hand tighten the flare nuts using three (3) or four (4) turns.

To finish tightening the flare nuts, use both a torque wrench and a backup wrench.

4. After all the piping has been connected and the caps have been tightened, check for refrigerant gas leaks

Loosening Flare Nuts

Always use two (2) wrenches to loosen flare nuts.

Piping Materials and Handling

Pipes used for the refrigerant piping system must include the specified thickness,

and the interior must be clean. While handling and storing, do not bend or damage

the pipes, and take care not to contaminate the interior with dust, moisture, etc.

Keep refrigerant pipe dry, clean, and airtight.

Keep Pipes Capped While Storing.

Clean

Airtight

No moisture should be inside the piping.

No dust should be inside the piping.

No leaks should occur.

Possible

Problems

- Significant hydrolysis of refrigerant oil.

- Refrigerant oil degradation.

- Poor insulation of the compressor.

- System does not operate properly.

- EEVs, capillary tubes are clogged.

- Refrigerant oil degradation.

- Poor insulation of the compressor.

- System does not operate properly.

- EEVs and capillary tubes become

clogged.

- Refrigerant gas leaks/shortages.

- Refrigerant oil degradation.

- Poor insulation of the compressor.

- System does not operate properly.

Solutions

- Remove moisture from the piping.

- Piping ends should remain capped until

connections are complete.

- Do not install piping on a rainy day.

- Connect piping properly at the unit’s side.

- Remove caps only after the piping is

cut, the burrs are removed, and after

passing the piping through the walls.

- Evacuate system to a minimum of 500

microns and insure the vacuum holds at

that level for 24 hours

- Remove dust from the piping.

- Piping ends should remain capped until

connections are complete.

- Connect piping properly at the side of

the unit.

- Remove caps only after the piping is cut

and burrs are removed.

- Retain the cap on the piping when

passing it through walls, etc.

- Test system for air tightness.

- Perform brazing procedures that comply

with all applicable standards.

- Perform flaring procedures that comply

with all applicable standards.

- Perform flanging procedures that

comply with all applicable standards.

- Ensure that refrigerant lines are pressure

tested to 550 psig.

Moisture

Dust

Leaks

Pipe Size (in. O.D.)

Outside Diameter (mm)

Tightening Torque (ft-lbs.)

1/4

6.35

13.0 - 18.0

3/8

9.52

24.6 - 30.4

1/2

12.7

39.8 - 47.7

5/8

15.88

45.4 - 59.3

3/4

19.05

71.5 - 87.5

Содержание ARNU073 B3G4

















































































Результаты поиска

Содержание ARNU073 B3G4

Отзывы:

Похожие инструкции для ARNU073 B3G4

Бренды по названию

Популярные бренды

LG ARNU073 B3G4, Руководство по установке

Результаты поиска

Содержание ARNU073 B3G4

Отзывы:

Похожие инструкции для ARNU073 B3G4

Бренды по названию

Популярные бренды