LG A6UW368FA0 Скачать руководство пользователя страница 6

Страница: 6 / 29

Room Air Conditioner

Installation of Indoor, Outdoor Unit

Installation of Indoor, Outdoor Unit

Read completely, then follow step by step.

Indoor unit

1. Do not have any heat or steam near the unit.

2. Select a place where there are no obstacles

in front of the unit.

3. Make sure that condensation drainage can be

conveniently routed away.

4. Do not install near a doorway.

5. Ensure the spaces indicated by arrows from

the wall, ceiling, fence or other obstacles.

6. Use a stud finder to locate studs to prevent

unnecessary damage to the wall.

Outdoor unit

1. If an awning is built over the unit to prevent

direct sunlight or rain exposure, make sure
that heat radiation from the condenser is not
restricted.

2. Ensure that the spaces indicated by arrows

around front, back and side of the unit.

3. Do not place animals and plants in the path

of the warm air.

4. Take the air conditioner weight into account

and select a place where noise and vibration
are minimum.

5. Select a place so that the warm air and noise

from the air conditioner do not disturb
neighbors.

Rooftop Installations:

If the outdoor unit is installed on a roof
structure, be sure to level the unit. Ensure the
roof structure and anchoring method are
adequate for the unit location. Consult local
codes regarding rooftop mounting.

Select the best location

More than 5cm

More than

5cm

More than 2.3m

More than

5cm

More than 10cm

More than 5cm

More than 2.3m

More than 5cm

More than 10cm

More than 50cm

More than 2m

More than 50cm

more than

70cm

more than

30cm

more than

30cm

CAUTION: Install the indoor unit
on the wall where the height from
the floors more than 2.3 meters.

Содержание A6UW368FA0






























Результаты поиска

Содержание A6UW368FA0

Отзывы:

Похожие инструкции для A6UW368FA0

Бренды по названию

Популярные бренды

LG A6UW368FA0, Руководство по установке

Результаты поиска

Содержание A6UW368FA0

Отзывы:

Похожие инструкции для A6UW368FA0

Бренды по названию

Популярные бренды