LG A6UW368FA0 Скачать руководство пользователя страница 22

Страница: 22 / 29

Room Air Conditioner

Checking the Drainage, Forming the Pipings and Long Pipe Setting

Forming the piping

Long Pipe Setting

Form the piping by wrapping the
connecting portion of the indoor
unit with insulation material and
secure it with two kinds of vinyl
tape.

• If you want to connect an additional drain

hose, the end of the drain outlet should be
routed above the ground. Secure the drain
hose appropriately.

In cases where the outdoor unit is
installed below the indoor unit
perform the following.

1. Tape the piping, drain hose and connecting

cable from down to up.

2. Secure the tapped piping along the exterior

wall using saddle or equivalent.

In cases where the Outdoor unit is
installed above the Indoor unit
perform the following.

1. Tape the piping and connecting cable from

down to up.

2. Secure the taped piping along the exterior

wall. Form a trap to prevent water entering
the room.

3. Fix the piping onto the wall by saddle or

equivalent.

1. Open the top cover of outdoor unit.

2. Select one of the two selectable modes as

follows.

3. Move the Slide swithc to "LONG" position.

4. Close the top cover and check whether the

product works normally.

WARNING: Do not open the top
cover or Set the pipe length
when operating the product.

• Trap is required to prevent water from entering

into electrical parts.

Taping

Drain hose

Pipings

Connecting
cable

Power supply
cord

Plastic
band

Seal a small
opening around
the pipings with
gum type sealer.

Trap

Seal a small opening
around the pipings
with gum type sealer.

Trap

Plastic
band

Seal a small
opening around
the pipings with
gum type sealer.

Trap

Seal a small opening
around the pipings
with gum type sealer.

NORMAL

LONG

Pipe length

Содержание A6UW368FA0






























Результаты поиска

Содержание A6UW368FA0

Отзывы:

Похожие инструкции для A6UW368FA0

Бренды по названию

Популярные бренды

LG A6UW368FA0, Руководство по установке

Результаты поиска

Содержание A6UW368FA0

Отзывы:

Похожие инструкции для A6UW368FA0

Бренды по названию

Популярные бренды