LG - Скачать руководство пользователя страница 55

Страница: 55 / 80

-55-

3. Compressor/Outdoor Fan are unable to drive.

Turn on Main Power

Operate "Cooling Mode(

)" by setting the desired temperature of the

remote controller is less than one of the indoor temperature by 1°C at least.

When in Air Circulation Mode, Compressor/Outdoor Fan is stopped.

Check the sensor for indoor temperature is attached as close as to be
effected by the temperature of Heat Exchanger(EVA).

When the sensor circuit for indoor temperature and connector are in bad
connection or are not engaged, Compressor/Outdoor Fan is stopped.

• Check the related circuit of R02H(12.1K), R01H(1.0K), R04H(6.2K),

R03H(1.0K) Micom (No.3.4) (Indoor unit).

• Check the indoor temperature sensor is disconnected or not(About 10k

Ω

/ at 25°C).

Turn off Main Power

• Check the electrical wiring diagram of outdoor side.
• Check the abnormal condition for the component of

Compressor/Outdoor Fan Motor.

• Check the "open" or "short" of conmecting wires between indoor and

outdoor.

Check Relay(RY - COMP) for driving compressor.

• When the power(About AC220V/240V) is applied to the connecting wire

terminal support transferred to compressor, PWB Ass'y is normal.

• Check the circuit related to the relay.

Check point

COMP ON

COMP OFF

Between Micom(No.

DC5V

DC0V

62) and GND

Between IC01M(No. 14)

Below DC 1V

About DC12V

and GND

(app)

Содержание -

















































































Результаты поиска

Содержание -

Отзывы:

Похожие инструкции для -

Бренды по названию

Популярные бренды

LG -, Руководство по обслуживанию

Результаты поиска

Содержание -

Отзывы:

Похожие инструкции для -

Бренды по названию

Популярные бренды