LG - Скачать руководство пользователя страница 53

Страница: 53 / 80

-53-

1. Product does not operate at all.

(* Refer to Electronic Control Device drawing and Schematic diagram.)

Electronic Parts Troubleshooting Guide

Turn off Main Power

Turn on Main Power

Does "beeping" sound is made from the Indoor Unit?

Primarily, the operating condition of Micom is OK.

Check the voltage of power(About AC 220V/AC240V, 50Hz)

• Main power's voltage
• Voltage applied to the unit
• Connecting method of Indoor/Outdoor connecting

cable

• Check PWB Ass'y

- Fuse
- Pattern damage
- Varistor(ZNR01J)

Check the connection housing for contacting

• Connector related to CN-POWER
• Connector related to CN-MOTOR
• Connector contacting of Outdoor Fan/Compressor
• Display PWB Ass'y Check

Check each load(Indoor/Outdoor Fan Motor,
Compressor, Stepping Motor) and contacting
condition of related connector

PCB Board Operation Check

Items

• Power Transformer

(Outdoor unit)
- Input Voltage
- Output Voltage

• IC01D(7812) Output

(Indoor/Outdoor unit)

• IC02D(7805) Output

(Indoor/Outdoor unit)

• IC01A(KIA7036, Reset IC)

X01(8MHz)

• Replace Trans

• Replace IC01D

• Replace IC02D

• Replace faulty parts

- About AC220V/240V±10% - Check the power voltage
- About AC14±3V

• DC +12V

• DC +5V

• Voltage of Micom No. 2,

(DC +4.5V over) and Soldering condition.

Content

Remedy

YES

(After 10 seconds)

Содержание -

















































































Результаты поиска

Содержание -

Отзывы:

Похожие инструкции для -

Бренды по названию

Популярные бренды

LG -, Руководство по обслуживанию

Результаты поиска

Содержание -

Отзывы:

Похожие инструкции для -

Бренды по названию

Популярные бренды