background image

12

EN

Installation Place Requirements

Location

125 cm

5 cm

5 cm

60 cm

10 cm

110 cm

135 cm

123 cm

2 cm

*125 cm

0.5 cm

*125 cm: minimum space for installation

Level floor

 : Allowable slope under the entire 

appliance is 1°.

Power outlet

 : Must be within 1.5 meters of 

either side of the location of the appliance.

Additional Clearance

 : 5 cm at the sides and 10 

cm behind the unit.

 

Do not place or store laundry products on top 

of the appliance at any time. These products 

may damage the finish or controls.

WARNING

 

The plug must be plugged into an appropriate 

outlet that is properly installed and grounded 

in accordance with all local codes and 

ordinances.

Positioning

 

Install the appliance on a flat hard floor. Then, 

level the Mini Washer before placing the Main 

washer on top. Lock only the rear feet of the 

Mini washer after leveling as the two front feet 

may need readjusting after the Main Washer 

has been placed on top.

 

Make sure that air circulation around the 

appliance is not impeded by carpets, rugs, etc.

 

Never try to correct any unevenness in the 

floor with pieces of wood, cardboard or similar 

materials under the appliance.

 

If it is impossible to avoid positioning the 

appliance next to a gas cooker or coal burning 

stove, an insulation (85x60 cm) covered with 

aluminum foil on the side facing the cooker 

or stove must be inserted between the two 

appliances.

 

Do not install the appliance in rooms where 

freezing temperatures may occur. Frozen 

hoses may burst under pressure. The reliability 

of the electronic control unit may be impaired 

at temperatures below freezing point.

 

Ensure that when the appliance is installed, it 

is easily accessible for an engineer in the event 

of a breakdown.

 

With the appliance installed, adjust all four 

feet using a transit bolt spanner to ensure 

the appliance is stable, and a clearance of 

approximately 5 mm is left between the top of 

the appliance and the underside of any work-

top.

 

If the appliance is delivered in winter and 

temperatures are below freezing, place the 

appliance at room temperature for a few hours 

before putting it into operation.

 

Do not use a drip pan as it can block the 

drawer. Using the drip pan may result in 

increased vibration and noise during operation.

WARNING

 

This appliance is not designed for maritime 

use or for use in mobile installations such as 

caravans, aircraft etc.

Electrical Connection

 

Do not use an extension cord or double 

adapter.

 

Always unplug the appliance and turn off the 

water supply after use.

 

Connect the appliance to an earthed socket in 

accordance with current wiring regulations.

 

The appliance must be positioned so that the 

plug is easily accessible.

 

Repairs to the appliance must only be carried 

out by qualified personnel. Repairs carried out 

by inexperienced persons may cause injury or 

serious malfunctioning. Contact your localan 

authorised LG repairer.

Содержание WTP20WX


















































Отзывы: