LFFH Metal Laboratory Casework Скачать руководство пользователя страница 22

Страница: 22 / 35

Wall Case Fillers

After positioning wall cases in a room, locate any wall case fillers that are required in the plan layout.

Installing Wall Case Front Fillers

Wall case front fillers are commonly used where a filler is needed between the front of a wall case and a wall.

Steps:

Using # 8 sheet metal screws, attach filler clips along the front edge of the wall case (vertically), as shown

below. Install two filler clips for 24” and 30” high wall cases; install three clips for 36” and 48” high units.

Also, attach one filler clip each along the top and bottom edges of the wall case.

Slide all three sides of the wall case front filler into the filler clips, as shown below. The filler is flexible,

and the top and bottom can be moved up or down slightly if necessary to fit into the clips. Front fillers

slide into place with a friction fit only. No additional fasteners are required.

Step A: Attach filler clip along the front, top and bottom edges.

Step B: Slide the wall case front filler into the filler clips.

Содержание Metal Laboratory Casework




































Результаты поиска

Содержание Metal Laboratory Casework

Отзывы:

Похожие инструкции для Metal Laboratory Casework

Бренды по названию

Популярные бренды

LFFH Metal Laboratory Casework, Руководство по установке

Результаты поиска

Содержание Metal Laboratory Casework

Отзывы:

Похожие инструкции для Metal Laboratory Casework

Бренды по названию

Популярные бренды