manualshive.com logo in svg

LFFH Metal Laboratory Casework, Руководство по установке, Страница: 7 / 35

Поделиться
Скачать
LFFH Metal Laboratory Casework Скачать руководство пользователя страница 7

4 

 

 

G.

 

Refer to the instructions above to adjust the spacing around the drawer front, if necessary. 

 

 

 

 

 

 

 

 

 

 

 

 

Door Adjustment 

 

Spacing of doors: 

 

For cabinets with recessed fronts, the proper spacing around a door is 0.125” (1/8”) on all sides, as shown above.  

The middle space (gap) between two doors is also 0.125”.   

 

For cabinets with overlay fronts, the spacing between the outside of a door and the side of the cabinet (

i.e.

, the 

side reveal) is 0.0625” (1/16”).  The vertical space between two doors, or between a door and a drawer front, is 

0.125”.       

 

Adjusting the door (hinge) up or down: 

 

Each door can be adjusted up or down slightly for spacing purposes by loosening the hinge screws and moving 

the hinge as necessary.  Be sure to tighten the screws securely when finished. 

 

 

Shelf Installation and Adjustment 

 

Shelves are supported by adjustable shelf clips.  Shelves are adjustable vertically in increments of 1.375”.   

 

Steps: 

A.

 

Mount clips in each of the four corners at the desired height. 

B.

 

Tilt the shelf at an angle to place it in the cabinet, being careful not to scratch the inside of the cabinet. 

C.

 

At extreme shelf locations (top or bottom), it may be desirable to mount the rear clips first, then place the 

shelf on them.  Then install the front clips while holding up the front of the shelf. 

 

 

 

 

Shelf Clip 

Shelf (shown tilted) 

Drawer Front  

Nylon Glide 

Drawer Body 

Screw (one per side) 

Содержание Metal Laboratory Casework




































Отзывы:

Нет отзывов