Lexmark 4500-00 Series Скачать руководство пользователя

Страница: 128 / 246

2-98

Service Manual

4500

Unexpected characters print or
characters are missing.

• Ensure correct printer driver is

being used.

• Press and hold

Continue

until all

lights come on to reset printer to
user default settings.

• Select hex trace mode to

determine what the problem is.

• Restore factory defaults.
• Make sure the parallel cable or

USB cable is firmly plugged in at
the back of the printer.

Jobs are not printing and the Error
light is on solid.

• Make sure the print cartridge is

installed properly.

• Make sure the printer top cover is

closed.

While in PostScript® 3 emulation,
the printer is flushing data
(Ready/Data and Error lights are
blinking).

• Ensure the correct PostScript

driver is being used.

• The Lexmark E220, E320, and

E321 do not support PostScript
emulation.

• The printer doesn’t have enough

memory to print the job. Install
more memory.

Manual duplex isn’t on the printer.

The printer driver may not support
manual duplex. Go to the Lexmark
Web site at www.lexmark.com to
download the latest printer driver.

While using manual duplex, the
printer gets a paper jam.

A paper jam interrupts the duplex
process. As a result, the information
on the page that jammed is lost.

• Press and release

Cancel

cancel the print job.

• Press and hold

Cancel

(approximately 3 seconds) to
reset the printer.

• Resend the print job.

Problem

Action

Содержание 4500-00 Series























































































































































































































































Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды

Lexmark 4500-00 Series, Руководство по обслуживанию

Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды