Lexmark 4500-00 Series Скачать руководство пользователя

Страница: 131 / 246

Diagnostic information

2-101

4500

Restoring factory defaults (E320/E322)

Sometimes resetting the printer to the original factory default
settings solves formatting problems.

1. Enter the special function menu. See

“Using the special

function menu (E320/E322) ” on page 2-105

for more

information.

2. Press and release the operator panel button twice quickly until

the Toner Low light comes on and the two bottom lights blink.

3. Press the operator panel button with a long button press (hold

until all the lights come on) to reset the printer to the original
factory defaults.

Once the settings are returned to the factory default values, the
printer returns to the

Ready

state.

Restoring factory defaults (E220/E321/E323)

1. Enter the configuration mode. See

“Using the special

function menu (E220/E321/E323) ” on page 2-106

for more

information.

2. After the four top lights are on, press and release

Cancel

3. Press and hold

Continue

until lights flash. The factory defaults

are reset.

4. To return the printer online, POR the printer.

Содержание 4500-00 Series























































































































































































































































Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды

Lexmark 4500-00 Series, Руководство по обслуживанию

Результаты поиска

Содержание 4500-00 Series

Отзывы:

Похожие инструкции для 4500-00 Series

Бренды по названию

Популярные бренды