Lexmark 2500 Series Скачать руководство пользователя страница 63

Страница: 63 / 85

Using Hex Trace mode

Hex Trace mode prints the control codes that are sent to the printer. Use this mode to help diagnose software/driver
problems.

Make sure the paper is loaded, and the ribbon cartridge is installed.

Turn the printer off.

Press and hold

Tractor

while turning the printer on.

Release

Tractor

when the lights go out.

Turn the printer off and back on again to exit Hex Trace mode.

Checking the printer status

Check the control panel lights and compare their status with the table information. Different patterns and
combinations of lights provide you with information about the condition of the printer and actions needed to correct
the condition.

Note:

Many error codes can be corrected by turning the printer off and back on again.

Printer status

Control panel lights

Status

Action required

Power

Ready

Paper Out

Off

Normal operating conditions. No action required.

Power

Ready

Paper Out

Off

Normal offline condition

Power

Ready

Paper Out

Off

Blinking

Load paper.

Press

Start/Stop

The Paper Out light goes off and the Ready light comes
on.

Note:

If you installed the optional Tractor 2 Feeder and

you are printing continuous forms, make sure the paper
select lever is in the continuous forms position.

Ready

Blinking

The printer has data in the buffer that needs to be
printed.

Troubleshooting

Содержание 2500 Series






















































































Результаты поиска

Содержание 2500 Series

Отзывы:

Бренды по названию

Популярные бренды

Lexmark 2500 Series, Руководство пользователя

Результаты поиска

Содержание 2500 Series

Отзывы:

Бренды по названию

Популярные бренды