background image

Mounting 

Strip

Inside Mount

Pre Drill 

3

8

Installation 

Hole

Bent Leaf 

Hinge

Window 

Opening

Outside Mount

3

8

" Installation  

Hole

Wall Face

Hole Locations

Hinges

Squareness Adjustments

Moves Right
Panel Up

Moves Right
Panel Down

Moves Left

Panel Up

Moves Left

Panel Down

Moves Left Panel Down  

and Right Panel Up

Moves Right Panel 
Down and Left Panel Up

A

C

B

STANDARD SHUTTER INSTALLATION

STANDARD SHUTTER INSTALLATION

6

7

Shutters Installation  Manual

Shutters Installation  Manual

STEP 5: FASTEN THE FRAME IN TWO POINTS 

Note: Review Packing Slip (Step 1) for further instructions on how to identify your frame and 

mount type.  

 

FASTEN FRAME FOR INSIDE MOUNT WITH Z, TRIM, BULLNOSE, DECOR TRIM OR L FRAME 

 

•   Center the assembled frame in opening, using the Product Labels to ensure the frame is right side up. 

 

•  Set one of the supplied screws through the pre-drilled hole on the upper left hand frame. Once secured,  

 

 

set one of the supplied screws through the pre-drilled hole on the upper right hand frame.

 

•  Be sure to fasten the screws through the frame and into the window jabs.

Note: 

When setting screws, seat screws fully, back out at least ½”, and then reseat (do not over-tighten).  

This will ensure your frame remains square during the installation process.

FASTEN FRAME FOR OUTSIDE MOUNT WITH L FRAME OR CASING FRAME

 

•  Center the frame on window opening, using the Product Labels to ensure the frame is right side up 

 

•  Set one of the supplied screws in the top of the left side frame pre-drilled hole. 

 

•   Place a level on the top frame, and move the right side frame until the frame is level.

 

•   Secure the top of the right frame to the wall using a supplied screw, keeping the frame level. 

Note: 

Do not over tighten the screws. Overtightening the screws will cause the frame to distort. 

FASTEN FRAME FOR INSIDE OR OUTSIDE MOUNT WITH MOUNTING STRIP

 

•   Drill installation holes, 

3

8

" diameter holes must be drilled at each hinge 

 

•  Using Product labels for guidance, place the side frame in opening with the frame right side up.

 

•   Insert a screw inside the top holes first, followed by the bottom ones while keeping panels plumb.

STEP 6: HANG PANELS

 

•  Set the panel(s) in the frame 

 

•  Insert the hinge pins into the hinges.

STEP 7:  SQUARE OR LEVEL PANELS TO THE OPENING (See Diagram at Right)  

Confirm that the panels are level/square by using a 
level. The panels should smoothly seat into the frame. 
If not, the following adjustment can be made  
to correct it.
 

•   Move bottom frame left or right (A) until the 

panel(s) are level with even gaps. Once the 
panels are confirmed to be level, hold the 
bottom frame and carefully insert a screw into 
the bottom frame.

Note:

 If you cannot achieve desired squareness, see 

troubleshooting section for additional tips to achieve a 
square panel.
Panel locks are located at the top and bottom of a 
shutter panel. They are used to keep panels securely 
closed and can also be used to level the panel.

FOR MOUNTING STRIP APPLICATIONS 

 

•   Adjust the bent-leaf hinges, if necessary, by loosening the hinge screws and moving the hinge left or right.  

Re-tighten hinge screws once the panel is confirmed to be level.

 
STEP 8: FASTEN REMAINING SCREWS   

 

•   Confirm the panels are square within the frame by using a level. Once the panels are level or has even light gaps, 

hold the bottom frame in position and set a screw in the 

middle bottom frame hole

.

 

•   Insert screws in the remaining holes, and check to ensure panels are level after every screw has been seated.

For Mounting Strip Applications

 

•  Center frame and insert screws

Note: 

Be careful not to over tighten the screws. Overtightening the screws may cause the frame to distort. 

For Window Shutters with T-Posts, please see Page 10 to mark the location (Step C) and secure the T-Post(s) onto the 
frame (Step D).

Содержание Shutters Remote Control






















Отзывы: