Levitronix LEVIFLOW LFSC-05D страница 12 Скачать руководство пользователя

Страница: 12 / 30

User Manual for LEVIFLOW

LFSC-D Flowmeters

www.levitronix.com

PL-4507-00, Rev08, DCO# 20-024

Installation

3.1 Installation of Converter LFC-1C-PC

3.1.1 Overview and Preparation

Figure 11: Single channel converter LFC-1C-PC

PIN

Designation

Specification

Standard Configuration

Description

DC24V+

Voltage: 24 VDC ±10%
Current: 150 mA
Inrush current: 4.4 A 2ms

Supply voltage

DC24V-

Field Ground

See note in installation

Section 3.1.2

Field ground

Analog Out +

4-20 mA or 0-20mA configurable
Load resistance < 600



Flow reading with 4-20 mA
Standard full scale flow range of each
sensor model.

Flow rate signal.
Update rate is 10ms.

Analog Out -

Digital Out1 +

Max. rating 30 V DC, 20 mA
Open collector
Configurable as Alarm High, Alarm Low,
Measurement Error, Volume Counter
Pulse, Volume Counter Alarm, Flow as
Frequency, Bubble Detect

- Parameter: Flow Alarm Low
- Setting: 12% of full scale
- Non contact type

Contact is made, when flow is below of 12% of
full scale.

Digital Out2 -

- Parameter: Measurement Error
- Non contact type

Contact is made, when measurement error is
occurred.

COM

Common Digital Out ground.

Digital In +

No-voltage contact or transistor oper.

Zero Adjustment

Is needed, if zero adjustment wants to be
triggered by PLC or when volume counter
function is used (integration of flow with volume
detection)

Digital In -

RS485 +

RS485

MODBUS

Protocol

Digital communication in a sensor array.
or configuration with service SW.

RS485 -

Table 9: Standard configuration of electrical interface (PLC and fieldbus)

Note 1: Min torque for connector screws is 0.5 Nm and max. is 0.6 Nm.

DIN Rail Mounting

Sensor Connectors

Interface Connector (12 Pin)

Re-Zero Button

High ADRS

LOW ADRS

4 Digit Display

LFC-1C-PC

Содержание LEVIFLOW LFSC-05D































Результаты поиска

Содержание LEVIFLOW LFSC-05D

Отзывы:

Похожие инструкции для LEVIFLOW LFSC-05D

Бренды по названию

Популярные бренды

Levitronix LEVIFLOW LFSC-05D, Руководство пользователя

Результаты поиска

Содержание LEVIFLOW LFSC-05D

Отзывы:

Похожие инструкции для LEVIFLOW LFSC-05D

Бренды по названию

Популярные бренды