Levitronix BFS-i06, Руководство пользователя

Страница: 14 / 20

User Manual for BFS-i06
www.levitronix.com
PL-3502-00, Rev00, DCO# 21-249
14
•
RS485 interface: To use RS485 as a control or service interface, an initialization resistor network
according to Figure 14 should be used to ensure stable communication and avoid disturbance effects.
For service and debugging purposes with the Levitronix
®
Service Software an RS485 to USB converter
cable (initialization network included) can be ordered according to Table 2 . Do not use multiple master
devices at the same time.
•
RS485 Fieldbus Multi-System Arrays: Several systems can be directly connected to the same
RS485 master. Following points and information shall be considered:
a. Address setting of the fan units can be done with the Levitronix
®
Service Software and a PC.
b. A termination resistor is recommended for long bus lengths. Do not use closed ring
arrangements. Contact
Levitronix
®
Technical Service department (see Section 6.3 ) for further
details and support.
Pin Wire Color Description Levels Notes
B4 Pink
Digital input 1
Enable / reset
5…24 V (min. 30 ms, edge triggered)

SPEED or PROCESS
or RESET
0 V (min. 30 ms, edge triggered)

STANDBY
Positive edge:
- Turns the system ON from state STANDBY
(PROCESS if digital input 2 is on, else SPEED)
- Resets the system from state ERROR
Recommended delay between reset and enable-on
positive edges: 500 ms
Negative edge:
- Turns the system OFF, if it was started by digital in 1
- Else no effect
Input logic may be inverted via Service Software or
Modbus protocol.
B5 Gray
Digital input 2
Process mode
5…24 V (min. 30 ms, edge triggered)

PROCESS Control
0 V (min. 30 ms, edge triggered)

SPEED Control
Switch between process control (closed loop pressure
or flow control) and speed control if system was
started by digital in 1.
Input logic may be inverted via Service Software or
Modbus protocol.
B3 Yellow Digital input ground Reference for digital inputs
B6 Violet
Analog input 1
Setpoint speed or
setpoint process value
Speed mode:
4…20 mA * =
0…13000 rpm *
Process mode:
4…20 mA * =
0…100 % *
Analog input 1 is enabled if the system was started by
a positive edge on digital input 1 and disabled as soon
as the power output is deactivated. Message 80h “PLC
analog input active” indicates that the input is active.
Setpoint speed or process requests over Modbus or
Service Software will be overridden when analog input
1 is active.
B1 Gray-pink
Analog input 2
Actual process value
(pressure or flow sensor)
4...20 mA * =
0…100% *
Connect to an external pressure or flow sensor to use
process control mode.
B2 Blue Analog input ground Reference for analog inputs
A2 Brown
Digital output 1
System state signal
Circuit closed

Power output ACTIVE
Circuit open

Power output NOT active
I
ndicates if the system’s power output is ON or OFF.
Ground (A4) is reference.
A3 White
Digital output 2
Error signal
Circuit closed

NO error present
Circuit open

ERROR(s) present
Indicates if errors are present.
Ground (A4) is reference.
A1 Blue-red
Analog output
Actual speed or
actual process value
Speed:
4...20 mA * =
0…13000 rpm *
Process value:
4…20 mA * =
0…100 % *
Assignment (speed / process / mode dependent) can
be changed via
Service Software or Modbus protocol.
Ground (A4) is reference.
A5 Brown-green RS485 +
Modbus protocol Termination resistors recommended
A6 White-yellow RS485 -
A4 White-green Ground GND / earth Internally connected to power - and cable shield
Table 6: Configuration of PLC connector for standard firmware
For other PLC configurations refer to alternate firmware documentation.
* Levels configurable in EEPROM editor of Levitronix
®
Service Software or through Modbus protocol.