Leviton PICCOLO SCAN Скачать руководство пользователя страница 30

Страница: 30 / 74

Leviton Piccolo Scan

12.1.1. Cue Lists in Submasters

A sequence of cues (cue list) can be executed in a submaster. The cues can be executed manually with the

submaster fader or automatically by pressing the [S#] key located above the fader.

For example, to load and execute a cue list in a submaster:

1. Press [CUE][#][THRU][#][LOAD][S#].

2. Move the S# fader from end to end, or press the [S#] key to automatically execute a crossfade.

To start the cue list with a blackout cue (cue 0): Press and hold [5.B]STEP then press [S#].

12.2. Submaster Playback

Press [FL.MT] to select the desired playback mode for submaster keys:

GO Mode

(LED Off)

In GO mode, pressing [S#] starts a submaster automatically.

For groups and cues:

Pressing [S#] starts an input fade from 0 to FF of a cue or group, using the input

time programmed (T ).

If the submaster is at FF: Pressing [S#] starts an output fade from FF to 0 of the cue

or group, using the output time programmed (T ).

If the submaster is not at 00 or FF: If the submaster has a time assigned pressing

[S#] will stop the current fade. If the submaster is stopped, pressing [S#] again will

restart the fade from the current level to FF.

After an automatic fade, the physical fader level and the output level may be

different. To take manual control with the fader, it is necessary to move the fader up

to the output level. At this moment, the console emits a “beep” and the fader is again

controlling the output level manually.

Flash Mode

(LED On)

In Flash mode, the

[

S#] keys behave as flash (bump) keys.

As long as a flash key is pressed, the submaster’s content level will be at FF (the

default level can be edited via [MENU 31]:Flash Level).

Solo Mode

(LED Blinking)

In Solo mode, when a solo-flash key is pressed, the submaster’s content level will be

at FF. At the same time, the output of all other active submasters is forced to 00.

It is also possible to influence the output of all other active submasters by

using the crossfader output. Select [MENU 31]:Solo Off X.

12.2.1. Normal, Absolute or Inhibit Modes

Submasters may operate in Normal, Absolute or Inhibit modes, depending on the group or cue that was

loaded into it:

Mode Options:

•

A cue/group loaded in Normal mode: Each submaster adds its content to the scene independently.

•

A cue/group loaded in Absolute mode: The submaster adds its content to the scene and forces the output

of all other submasters to zero. The result is similar to the solo-flash function but with fading.

•

A cue/group loaded in Inhibit mode: The submaster does not add its content to the scene but will remove

it if content is active from any other submaster or from the crossfader.

Содержание PICCOLO SCAN











































































Результаты поиска

Содержание PICCOLO SCAN

Отзывы:

Бренды по названию

Популярные бренды

Leviton PICCOLO SCAN, Руководство пользователя

Результаты поиска

Содержание PICCOLO SCAN

Отзывы:

Бренды по названию

Популярные бренды