LevelOne GEP-2450 Скачать руководство пользователя страница 16

Страница: 16 / 110

2. Installation

This section will give users a quick start for:

2-1. Starting 24-Port GbE Web Smart PoE Switch Up

Hardware and Cable Installation

- Management Station Installation

- Software booting and configuration

2-1-1. Hardware and Cable Installation

At the beginning, please do first:

⇒

Wear a grounding device to avoid the damage from electrostatic discharge

⇒

Be sure that power switch is OFF before you insert the power cord to power

source

• Installing Optional SFP

Fiber Transceivers to the

Note: If you have no modules, please skip this section.

24-Port GbE Web Smart

Switch

• Connecting the SFP Module to the Chassis:

The optional SFP modules are hot swappable, so you can plug or unplug it
before or after powering on.

1. Verify that the SFP module is the right model and conforms to the chassis

2. Slide the module along the slot. Also be sure that the module is properly

seated against the slot socket/connector

3. Install the media cable for network connection

4. Repeat the above steps, as needed, for each module to be installed into

slot(s)

5. Have the power ON after the above procedures are done

•

TP Port and Cable Installation

Fig. 2-1 Installation of Optional SFP

Fiber Transceiver

Содержание GEP-2450















































































































Результаты поиска

Содержание GEP-2450

Отзывы:

Похожие инструкции для GEP-2450

Бренды по названию

Популярные бренды

LevelOne GEP-2450, Руководство пользователя

Результаты поиска

Содержание GEP-2450

Отзывы:

Похожие инструкции для GEP-2450

Бренды по названию

Популярные бренды