manualshive.com logo in svg

Leuze electronic MSI-MD-FBX, Оригинальная инструкция по эксплуатации, Страница: 32 / 47

Поделиться
Скачать
Leuze electronic MSI-MD-FBX Скачать руководство пользователя страница 32

Starting up the device - Configuration

Leuze electronic

MSI-MD-FBX

32

DIP

switch

Function

ON

OFF

7/8

Muting timeout

OFF/OFF: 20 seconds

OFF/ON: 2 minutes

ON/OFF: 10 minutes

ON/ON: 100 hours

Setting the operating mode

The following table lists the permissible operating modes that can be set via the DIP switch blocks.

After the device is started, the 7-segment display of the muting controller shows the set operating mode.

NOTICE

This muting controller can only be operated in operating mode 7.

NOTICE

Error in event of impermissible setting of DIP switches!

If a DIP switch configuration is set that does not correspond to that of a permissible operating
mode, an operating mode error is triggered and the OSSDs switch off.

Ä

Only set one of the DIP-switch configurations listed in the operating mode table.

NOTICE

Restart interlock for access guarding!

For access guarding, a restart interlock is required.

Ä

If the 

automatic restart interlock

 is configured in the muting controller, you must carry out the

restart interlock, e. g. via the machine interface.

Tab. 8.2: 

Operating modes

DIP

switch

1

2

3

4

5

6

Function

Number of

muting sen-

sors

Muting mode

EDM

Restart

Muting-en-

able

Muting-time-

out exten-

sion

Operating

mode

7

2-sensor

Timing con-
trolled

Without

Manual

With

Without

Содержание MSI-MD-FBX
















































Отзывы:

Нет отзывов