Leuze electronic BPS 301i Скачать руководство пользователя

Страница: 63 / 93

Leuze electronic webConfig tool – Extended configuration

Leuze electronic

BPS 301i

Configuration of position detection (

DATA PROCESSING

tab,

Position

Detection

)

• Integration depth

Number of successive measurements that the BPS uses for position determination.

• Scaling free resolution

Free scaling of the output of the position values.

• Preset

A preset position value (preset value) is activated at an appropriate position.

• Offset

Output value=measurement value+offset

If a preset is active, this has priority over the offset.

• Error handling procedures

Parameters for the position value in case of failure.

Configuration of position monitoring (

DATA PROCESSING

tab,

Position

Monitoring

)

• Position limit value 1/2

Signals that the position value is outside of the configured limit value range.

Configuration of speed detection (

DATA PROCESSING

tab,

Speed

Detection

)

• Speed measurement averaging

Measurement value preparation averages all speed values calculated during the selected period

(averaging) to yield a speed output value.

• Scaling free resolution

Free scaling of the output of the speed values.

• Error handling procedures

Parameters for the speed value in case of failure.

Configuration of speed monitoring (

DATA PROCESSING

tab,

Measurement data

Speed

Monitoring

)

• Speed limit value 1-4

Signals that the speed is outside of the configured limit value range.

Configuration of the measurement value display (

DATA PROCESSING

tab,

General preparation

)

Unit of measurement: metric or inch

• Counting direction

Count direction for position calculation or sign for speed calculation.

• Output mode sign

Output mode of the sign. Affects position value and speed output.

Configuration of monitoring of the reading quality (

DATA PROCESSING

tab,

Reading quality

)

• Warning threshold for reading quality in %
• Error threshold for reading quality in %

Configuration of the communication data (

COMMUNICATION

tab)

• Configuration of the SERVICE USB interface
• Setting the process interface

• Baud rate: 4,800 baud … 115,200 baud

• Data format: 8N1, 8E1, 8O1, 8N2

9.3.3

ALIGNMENT

function

NOTICE

ALIGNMENT

function only in the

Service

operating mode!



The BPS can only be aligned using the

ALIGNMENT

function in the

Service

operating mode.

Содержание BPS 301i






























































































Результаты поиска

Содержание BPS 301i

Отзывы:

Похожие инструкции для BPS 301i

Бренды по названию

Популярные бренды

Leuze electronic BPS 301i, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание BPS 301i

Отзывы:

Похожие инструкции для BPS 301i

Бренды по названию

Популярные бренды