Leuze electronic BPS 301i Скачать руководство пользователя

Страница: 26 / 93

Functions

Leuze electronic

BPS 301i

Functions

This chapter describes the functions of the BPS and the parameters for adaptation to the respective appli

cation conditions and requirements.
The parameters are set via the webConfig tool; see chapter 9 "Leuze electronic webConfig tool –

Extended configuration".

Main functions:

• Position measurement
• Speed measurement

The following parameters are relevant for the timing of the position and speed measurement:

• Measurement value preparation

Configurable response time

• Measurement error tolerance

Configurable time-based error suppression

4.1

Position measurement

The output value of the position measurement is calculated from the measurement and the settings for

resolution, preset, offset, etc.
The most important individual parameters for the position measurement are:

4.2

Speed measurement

The current speed is ascertained and output on the basis of the respective position values.
The most important individual parameters for the speed measurement are:

Parameter

Description

Range/Values

Position resolution

The parameter specifies the resolution of the position value.

It acts only on the host interface.

The resolution has no effect on the set parameter values

such as offset or preset.

0.001 mm

0.01 mm

0.1 mm

1 mm

10 mm

free resolution

Unit

The parameter specifies the measurement unit of the mea

sured position and speed.

The selection of the measurement unit affects all parame

ters with measurement units.

Metric (mm)

inch (1/100 in)

Offset

The offset is used to correct the position value by a fixed

amount.

If the offset is activated, the offset is added to the position

value. This yields a new output value:

Output value = position value + offset

1 mm

inch/100

Preset

Like the offset, the preset is used to correct the position

value.

With preset, a preset value is specified. The value is

accepted during a corresponding event (switching input or

fieldbus).

If the preset is activated, this has priority over the offset.

1 mm

inch/100

Содержание BPS 301i






























































































Результаты поиска

Содержание BPS 301i

Отзывы:

Похожие инструкции для BPS 301i

Бренды по названию

Популярные бренды

Leuze electronic BPS 301i, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание BPS 301i

Отзывы:

Похожие инструкции для BPS 301i

Бренды по названию

Популярные бренды