5.1.1
Menu items factory settings, data import and
export
5.2
Supplements to the individual items in the
configuration menu
5.2.1
Start Delay
The delay configured will only be active after a loss in power
(staggered start in projects). For each further start, the pumps will
immediately turn on when they are triggered via the level.
5.2.2
Lowest level configurations (On/Off)
If a switch-on point lower than 5 cm is selected, then the software will
automatically use 5 cm as the switch-on point. If a switch-off point
lower than 3 cm is selected, then the software will automatically use
3 cm as the switch-off point. This also applies to starting overrun
time, which will then start at 3 cm. This is necessary for the safe
operation of the switchgear system.
5.2.3
Stop Delay, Overrun
Overrun facilitates draining below the level sensor, e.g. for dynamic
pressure systems.
5.2.4
Runtime monitoring, Running time max.
The menu can be used to access the item maximum runtime. In the
default setting, this value is set to zero, i.e. the function is disabled.
When a value of 1 – 60 minutes is set, then
a deactivation of the pump occurs when the pump runs without
interruption for longer than the set value. Moreover, an alarm will be
triggered and a corresponding error report will be shown on the
display. The pump will not run again until the error has been
confirmed. The runtime monitoring applies to both the automatic as
well as the manual mode.
5.2.5
Current monitoring (max. current)
The nominal current of the corresponding pumps can be set
immediately. The software in the control adds a certain percentage
to the set value to compensate tolerances. The triggering occurs
according to an I² / t function and with this, the increased initial
current of the pump is taken into account.
5.2.6
Inspection
The
PS
MEGA
1
can issue a message on the display on when servicing
is to be performed.
The configuration possibilities are 90, 180 or
365 days. The function can also be turned off at this point in the
menu (factory settings).
Only service personnel are able to change or reset the
settings.
5.2.7
Th. fault 1, Th. fault 2
For pumps whose temperature monitoring consists of only one
bimetallic contact per pump, thermal error 1 can be deactivated
accordingly in the menu. Thermal error 2 cannot be turned off in the
menu.
5.2.8
Error memory, Last fault
The last 4 errors that occurred remain stored in non-volatile memory
and can be retrieved in the menu under “Last fault”.
Caution Last
fault 1 is the last fault that occurred. If “Last fault 1” is called up in the
menu, the last errors can be deleted from the memory with the
acknowledge button.
5.2.9
Rotary field error
The rotary field monitoring monitors both the phase sequence as
well as the lack of a phase. The pumps are locked in the event of a
phase error, an alarm is issued and the message “Rotary field error”
appears on the display. The rotary field monitoring can be activated
and deactivated via the menu.
The rotary field monitoring must be switched during
the operation of 1~ motors.
5.2.10
3~ monitoring
Display, evaluation and monitoring of the motor current on all three
phases. In the event of the deactivation of the 3~ monitoring, only a
single phase (L1) is monitored. This enables the operation of 1~
motors. (See page 10, point 7. Electrical connection)
5.2.11
ATEX – Mode
ATEX mode has to be activated for pumps implemented in EX zones.
ATEX mode impedes the pumps from being turned on via manual
function, via forced switch-on or via remote control system until the
switch-off point is met. If the pumps are started via the overrun time
or manual function while the switch-off point is exceeded, then
draining can occur below the switch-off point.
The manual function will be automatically interrupted after
2 minutes. When the ATEX function hinders pumps from turning on,
the display will show the report
“ATEX: Level below switch-off point.”
5.2.12
Service – Mode
The default setting is for service mode to be activated, i.e. all setting
can be changed. When the service mode is turned off in the menu,
the settings can only be queried using the digital potentiometer.
When the service mode is deactivated, no settings can be
changed other than the local language.
Menüpunkt
Erklärung
Preferences reset
All settings can be reset with this function.
Attention:
Pump starts, operating hours,
error memory and maintenance status are
preserved.
FatFS: Filename
An input menu can be opened here to assign
a file name. Now the current settings and log
files can be saved under this file name.
FatFS: Read
The file with the setting parameters is read
by the SD card
FatFS: Write
The file with the current parameters is
written by the SD card.
FatFS: Log
The operating hours, pump starts and error
notifications are transferred to the memory
card.
PS
MEGA
1
www.lesa.de
7
