background image

No.

Description

No.

Description

No.

Description

Wound stator

DE bearing

Fixing screw for no. 70

Wound armature

DE bearing retainer 

Terminal box lid

Drive end shield (DE)

Fixing screw for retainer no. 33

Screw for lid no. 74

Non drive end shield (NDE)

DE bearing preloading (wavy) washer

Seal for lid no. 74

DE shield fixing screw

DE bearing circlip

Cable gland support plate

Shaft extension key

NDE bearing

Seal for plate no. 81

Shaft extension washer

Retainer (for motor with no options fitted)

Fixing screw for plate no. 81

Shaft extension screw

NDE bearing circlip

Terminal block

Lifting ring

Fixing screw for retainer

 no. 52 (and/or 160)

Terminal box base plate

Identification plate

Terminal box seal

Fan grille

Fixing screw

Terminal box

Fixing screw for grille no. 110

LSK
D.C. motors

15.2 - LSK 1804, 1804C, 2004C, 2254C, 2504C & 2804C

110

111

402

401

25

23

40

5

14

28

30

33

21

3

1

A

26

22

44

46

D

D

81

83

69

70

77

74

92

75

82

84

12

LSK motor model 1804 to 2804C

1

30

72

3

33

74

5

40

75

6

44

77

14

46

81

21

50

82

22

52

83

23

60

84

25

62

92

26

69

110

28

70

111

*: number linked to an option.

Содержание LSK 1122

















Отзывы: