Lenze MC-PBM Скачать руководство пользователя страница 40

Страница: 40 / 46

Electrical installation

Wiring and Configuration
MC−PNC, MC−PND

BA_MC−Card EN 1.0

How to install the device driver:

1. Switch on the IPC after installing the communication card.

The operating system recognises the new hardware and the "Found New Hardware
Wizard" starts.

2. Select

Install from a list or specific location

3. Insert the "PC based Automation" DVD into the DVD drive and click

Next.

4. Select the

Search the best driver in these locations

option field and the

exchangeable disk storage (floppy disk, CD,..)

control field in the following dialog.

5. Click

Next.

The CifX driver is installed. The installation progress is displayed. At the end, the wizard
reports that the software for the "cifX PCI/PCIe Device" has been installed.

6. Click

Complete

7. Check if the communication card has been installed correctly:

– Start the

Windows

system control

– If you have set the "classic view", double−click the

System

entry. If you have set the

"category view", select

Performance and Maintenance

System

– Select the

Hardware

The device manager is opened. If no error is reported under "CIFx Communication
Interface"

"CifX PCI/PCIe Device", the communication card has been installed

correctly.

Содержание MC-PBM















































Результаты поиска

Содержание MC-PBM

Отзывы:

Бренды по названию

Популярные бренды

Lenze MC-PBM, Руководство по эксплуатации

Результаты поиска

Содержание MC-PBM

Отзывы:

Бренды по названию

Популярные бренды