background image

Product description

Variants

MC−ISI

3

     

l

 15

BA_MC−Card   EN   1.0

Technical data

MC−ISI

Conformity, approval, directive

Conformity

CE

EN 61000−6−4
EN 61000−6−2

EMC Directive Class A,
industrial premises

Approval

UR

UL 508
CSA C22.2

Process Control Equipment 
(File−No. E236341)

Directive

RoHS

Products lead−free in accordance with CE
Directive 2011/65/EU

General data and operating conditions

See standard device

Electrical data

Current

< 0.2 A

at standard device supply voltage of 24 V

Electrical isolation to the
fieldbus

yes

Mechanical data

Mass

< 0.1 kg

Communication

Type

Serial interface

COM A

Type

RS232, electrically isolated

Isolation

2.500 Vrms

ESD protection

15 kV

COM B

Type

RS422/485 (switchable), electrically isolated

Isolation

2.500 Vrms

ESD protection

15 kV

Baud rate

600 Baud ... 115.2 kBaud

Data frame

5, 6, 7, 8 and 9 Bit

Parity

Even, odd, none, space & mark

¸

O

Warnings!

Use only together with appropriate cable connectors, provided with screws for
securement and secure connector to avoid loosening.
For use in controlled environment only.

¹

O

Warnings!

A utiliser exclusivement avec des connecteurs de câble à vis adaptés. Fixer les
connecteurs pour éviter toute déconnexion.
Destiné uniquement à des zones à environnement contrôlé.

Содержание MC-PBM















































Отзывы: