manualshive.com logo in svg

Lenze MC-PBM, Руководство по эксплуатации

Поделиться
Скачать
Lenze MC-PBM Скачать руководство пользователя страница 23

Electrical installation

Important notes

4

     

l

 23

BA_MC−Card   EN   1.0

4

Electrical installation

4.1

Important notes

(

Stop!

Short circuit and static discharges

The printed circuit board and the standard device contain components which
are endangered in the case of short circuit or static discharge.

Possible consequences:

ƒ

The printed circuit board or devices connected are destroyed.

Protective measures:

ƒ

For all operations on the printed circuit board, the latter as well as the
standard device have to be in a deenergised state. This in particular applies
to the connection/disconnection of the printed circuit board and the
connection/disconnection of connectors.

ƒ

All persons handling printed circuit boards must regard ESD measures.

ƒ

Connector contacts must not be touched.

ƒ

Printed circuit boards must only be touched in contact−free places and must
only be placed on suitable bases (e. g. on ESD packaging or conductive
foamed material).

ƒ

Printed circuit boards must only be transported and stored in ESD
packaging.

)

Note!

For mounting the unit, the housing of the industrial PC has to be opened
(

^

 documentation for the standard device).

4.2

Mounting

SPEED

MC-ET

H

RJSS

-5381

RJSS-5381

SPEED

LINK

LAN

MC-ET

H

RJSS

-5381

RJSS-5381



‚

ƒ

ACTI

VE

LINK

PROFI

NET

MC-PNx

RJSS

-5381

RJSS-5381

RJSS

-5381

RJSS-5381

SYS

ST0

ST1

ST2

LINK

LAN

ACTI

VE

LINK

PROFI

NET

MC-PNx

RJSS

-5381

RJSS-5381

RJSS

-5381

RJSS-5381

SYS

ST0

ST1

ST2

MC−PNx−002

Содержание MC-PBM















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды