Lenze E70AC Series Скачать руководство пользователя страница 99

Страница: 99 / 162

Electrical installation

Installation according to EMC (installation of a CE−typical drive system)

Wiring outside of the control cabinet

EDS700ACBA EN 5.1

6.3.5

Wiring outside of the control cabinet

Notes for cable routing outside the control cabinet:

The longer the cables the greater the space between the cables must be.

If cables for different signal types are routed in parallel, the interferences can be
minimized by means of a metal barrier or separated cable ducts.

over

arrier without

opening

Power ca

les

Signal ca

les

EMVallg001

Fig. 6−3

Cable routing in the cable duct with barrier

over

ommunication ca

les

uct

easuring ca

les

Analog ca

les

ontrol ca

les

Power ca

les

EMVallg002

Fig. 6−4

Cable routing in separated cable ducts

Wiring on the motor side

)

Note!

The motor cable is highly susceptible to interference. Therefore you will
achieve an optimum wiring on the motor side if you

exclusively use shielded and low−capacitance motor cables.

not

integrate any further cable into the motor cable (e.g. for blowers

etc.).

shield the supply cable for temperature monitoring of the motor (PTC or
thermostat) and install it separately from the motor cable.

Содержание E70AC Series



































































































































































Результаты поиска

Содержание E70AC Series

Отзывы:

Похожие инструкции для E70AC Series

Бренды по названию

Популярные бренды

Lenze E70AC Series, Руководство по оборудованию

Результаты поиска

Содержание E70AC Series

Отзывы:

Похожие инструкции для E70AC Series

Бренды по названию

Популярные бренды