Lenovo tihnkserver rd330 Скачать руководство пользователя страница 42

Страница: 42 / 198

ThinkServer RAID 500 Adapter (also known as ThinkServer 9240-8i RAID 0/1 Adapter)

The following illustration shows the connectors on the ThinkServer RAID 500 Adapter.

Figure 15. ThinkServer RAID 500 Adapter

Port 0

ThinkServer RAID 500 Upgrade Key for Advanced RAID

connector

Port 1

Port 0

Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 31.

Port 1

Used to connect a mini-SAS signal cable. See “Mini-SAS to mini-SAS signal cable connections” on page 31.

ThinkServer RAID 500 Upgrade Key for Advanced RAID connector

Used to connect a ThinkServer RAID 500 Upgrade Key for Advanced RAID. See “Installing or removing the
ThinkServer RAID 500 Upgrade Key for Advanced RAID” on page 91.

ThinkServer RD330 Hardware Maintenance Manual

Содержание tihnkserver rd330







































































































































































































Результаты поиска

Содержание tihnkserver rd330

Отзывы:

Бренды по названию

Популярные бренды

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание tihnkserver rd330

Отзывы:

Бренды по названию

Популярные бренды