Lenovo tihnkserver rd330 Скачать руководство пользователя страница 103

Страница: 103 / 198

9. Note the orientation of the low-profile bracket and position it on the RAID card. Align the two screw

holes in the low-profile bracket with the corresponding screw holes in the RAID card, and then install the
screws to secure the bracket.

Figure 44. Installing the low-profile bracket to the RAID card

10. Position the RAID card near the PCI Express card slot. Ensure that the left edge of the RAID card is

inserted into the notch of the RAID card retention bracket

. Then, carefully press the RAID card

straight into the slot until it is securely seated and the low-profile bracket also is secured by the riser
card assembly 2.

Figure 45. Installing the RAID card

11. Connect signal cables to the connectors on the new RAID card and the connectors on the hot-swap

hard disk drive backplane. See “Mini-SAS to mini-SAS signal cable connections” on page 31.

12. Reinstall the riser card assembly 2. The procedure is similar to that of the riser card assembly 1. See

“Replacing the riser card assembly 1” on page 145.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation, go to “Completing the parts replacement” on page 155. Then, configure

RAID for your server. See “Configuring RAID” on page 58.

Chapter 6

Installing, removing, or replacing hardware

Содержание tihnkserver rd330







































































































































































































Результаты поиска

Содержание tihnkserver rd330

Отзывы:

Бренды по названию

Популярные бренды

Lenovo tihnkserver rd330, Руководство по техническому обслуживанию аппаратной части

Результаты поиска

Содержание tihnkserver rd330

Отзывы:

Бренды по названию

Популярные бренды