Lenovo ThinkSystem SR550 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 206

background image

8

Power supply 1

The hot-swap redundant power supplies help you avoid significant interruption to the operation of the
system when a power supply fails. You can purchase a power supply option from Lenovo and install the
power supply to provide power redundancy without turning off the server. On each power supply, there are
three status LEDs near the power cord connector. For information about the status LEDs, see “Rear view
LEDs” on page 24.

9

NMI button

Press this button to force a nonmaskable interrupt (NMI) to the processor. By this way, you can blue screen
the server and take a memory dump. You might have to use a pen or the end of a straightened paper clip to
press the button.

10 11

USB 3.0 connectors

Used to attach a device that requires a USB 2.0 or 3.0 connection, such as a keyboard, USB mouse, or USB
storage device.

12

VGA connector

Used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a VGA
connector.

13

Ethernet connector 2

14

Ethernet connector 1

Used to attach an Ethernet cable for a LAN. The Ethernet connector has two status LEDs to help you identify
the Ethernet connectivity and activity. See “Rear view LEDs” on page 24.

Ethernet connector 1 can be set as XClarity Controller network connector. To set Ethernet connector 1 as
XClarity Controller network connector, start Setup utility, go to

BMC Settings

➙

Network Settings

➙

Network Interface Port

and select

Shared

. Then, go to

Shared NIC on

and select

Onboard Port 1

.

15

XClarity Controller network connector

Used to attach an Ethernet cable to manage the system using XClarity Controller.

16

Ethernet connector on the LOM adapter

Used to attach an Ethernet cable.

17

Ethernet connector on the LOM adapter

This Ethernet connector can be set as XClarity Controller network connector. To set the Ethernet connector
as XClarity Controller network connector, start Setup utility, go to

BMC Settings

➙

Network Settings

➙

Network Interface Port

and select

Shared

. Then, go to

Shared NIC on

and select

PHY Card

.

Rear view LEDs

There are several LEDs on the rear of the server.

The following illustration shows the LEDs on the rear of the server.

24

ThinkSystem SR550 Maintenance Manual

«
...
30
31
32
33
34
...
»

Содержание ThinkSystem SR550















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkSystem SR550

Бренд: Emcore Страницы: 13

HSP-176M-1500-HD

Бренд: Baileigh Industrial Страницы: 44

A-B Quality 1606-XLP30

Бренд: Rockwell Automation Страницы: 4

Carlyle ETW12FL

Бренд: Napa Страницы: 18

Бренд: Graco Страницы: 2

Бренд: Wacker Neuson Страницы: 30

Бренд: Campbell Hausfeld Страницы: 16

Бренд: Milwaukee Страницы: 70

Бренд: Ryobi Страницы: 13

MAXIMUM 054-1232-4

Бренд: MasterCraft Страницы: 19

Бренд: New World Technologies Страницы: 31

Бренд: Parkside Страницы: 38

Бренд: patura Страницы: 76

Carlyle Tools 6-711A

Бренд: Napa Страницы: 16

Бренд: M-system Страницы: 4

Бренд: OfiTE Страницы: 20

Carlyle TW12RH2

Бренд: Napa Страницы: 12

ecomat300 AC1220

Бренд: IFM Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды