Lenovo ThinkCentre 5110 Скачать руководство пользователя

Страница: 94 / 128

5. Reinstall all the 11 screws that secure the main bracket to the front bezel.

6. Reinstall the optical drive. See “Installing an optical drive” on page 82.

7. Reinstall the heat sink assembly. See “Installing the microprocessor and heat sink assembly” on page 90.

8. Close the system board shielding. See “Closing the system board shielding” on page 76.

9. Go to “Completing the FRU installation” on page 109.

Replacing the microprocessor and heat sink assembly

CAUTION:

The microprocessor and heat sink assembly might be very hot. Turn off the computer

and wait three to five minutes to let the computer cool before opening the computer cover.

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important Safety
Information” on page 1.

This section provides instructions on how to replace the microprocessor and heat sink assembly.

ThinkCentre Hardware Maintenance Manual

Содержание ThinkCentre 5110

































































































































Результаты поиска

Содержание ThinkCentre 5110

Отзывы:

Похожие инструкции для ThinkCentre 5110

Бренды по названию

Популярные бренды

Lenovo ThinkCentre 5110, Руководство по обслуживанию

Результаты поиска

Содержание ThinkCentre 5110

Отзывы:

Похожие инструкции для ThinkCentre 5110

Бренды по названию

Популярные бренды