Lenovo ThinkCentre 5110 Скачать руководство пользователя

Страница: 93 / 128

12. Lift the main bracket up a little bit so that the LCD panel detaches from the main bracket, and you can

gently pull out the microprocessor fan assembly cable connectors through the hole in the main bracket.

13. Lift the microprocessor fan assembly and cables up and out of the main bracket.

Installing a microprocessor fan assembly

To install a microprocessor fan assembly, do the following:

1. Reinstall the four screws that attach the new microprocessor fan assembly to the main bracket.

2. Lift the main bracket up so that you can route the microprocessor fan assembly cables through the hole

in the main bracket. Connect the microprocessor fan assembly cables to the system board connectors.

3. Route the microprocessor fan assembly cables so that they will not be pinched by the system board

shielding.

4. Reinstall the four screws that attach the LCD panel to the main bracket.

Chapter 9

Replacing FRUs

Содержание ThinkCentre 5110

































































































































Результаты поиска

Содержание ThinkCentre 5110

Отзывы:

Похожие инструкции для ThinkCentre 5110

Бренды по названию

Популярные бренды

Lenovo ThinkCentre 5110, Руководство по обслуживанию

Результаты поиска

Содержание ThinkCentre 5110

Отзывы:

Похожие инструкции для ThinkCentre 5110

Бренды по названию

Популярные бренды