manualshive.com logo in svg

Lenovo ThinkCentre 0401, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo ThinkCentre 0401 Скачать руководство пользователя страница 80

Miscellaneous error messages

Message/Symptom

FRU/Action

Changing display colors

Display/Monitor

Computer will

not

power-off. See “Power

Supply Problems” on page 49.

1.

Power Switch

2.

System Board

3.

Riser card, if installed

Computer will

not

RPL from server

1.

Ensure that network is in startup
sequence as first device or first device
after diskette

2.

Ensure that network adapter is enabled
for RPL

3.

Network adapter (Advise network
administrator of new MAC address)

Computer will

not

perform a Wake On

LAN

®

(if applicable)

1.

Check power supply and signal cable
connections to network adapter

2.

Ensure that the operating system settings
are set to enable Wake on LAN

®

3.

Ensure Wake On LAN feature is enabled
in Setup/Configuration (see “Starting the
Setup Utility program” on page 45)

4.

Ensure network administrator is using
correct MAC address

5.

Ensure no interrupt or I/O address
conflicts

6.

Network adapter (advise network
administrator of new MAC address)

Dead computer. See “Power Supply
Problems” on page 49.

1.

Power Supply

2.

System Board

Diskette drive in-use light remains on or
does not light when drive is active.

1.

Diskette Drive

2.

System Board

3.

Diskette Drive Cable

Flashing cursor with an otherwise blank
display.

1.

System Board

2.

Primary Hard Disk Drive

3.

Hard Disk Drive Cable

Incorrect memory size during POST

1.

Run the Memory tests

2.

Memory Module

3.

System Board

″

Insert a Diskette

″

icon appears with a

known-good diagnostics diskette in the first
3.5-inch diskette drive.

1.

System Board

2.

Diskette Drive Cable

3.

Network Adapter

Intensity or color varies from left to right of
characters and color bars

1.

Display

2.

Video adapter (if present)

3.

System Board

No power or fan not running

1.

See “Power Supply Problems” on page
49.

74

Hardware Maintenance Manual

Содержание ThinkCentre 0401











































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды