manualshive.com logo in svg

Lenovo ThinkCentre 0401, Руководство по техническому обслуживанию аппаратной части

Поделиться
Скачать
Lenovo ThinkCentre 0401 Скачать руководство пользователя страница 102

6.

Firmly press the memory module

1

straight down into the slot by applying

pressure on both ends of the memory module simultaneously. The retaining
clips

2

snap into the locked position when the memory module is firmly

seated in the slot.

Note:

If there is a gap between the memory module and the retaining clips, the
memory module has not been correctly inserted. Open the retaining
clips, remove the memory module, and then reinsert it.

7.

Go to “Completing the FRU installation” on page 125.

Replacing the microprocessor fan assembly

Attention

Do not open your computer or attempt any repair before reading and understanding the
“Important safety information” in the

ThinkCentre Safety and Warranty Guide

that came with

your computer. To obtain a copy of the

ThinkCentre Safety and Warranty Guide

, go to:

http://www.lenovo.com/support

This section provides instructions on how to replace the microprocessor fan
assembly.

Removing the microprocessor fan assembly

To remove the microprocessor fan assembly, do the following:

1.

Turn off the computer.

2.

Disconnect all cables, power cords, and external options from your computer.
See “Rear connectors” on page 78.

3.

Place a soft, clean towel or cloth on the desk or surface. Hold the sides of
your computer and gently lay it down so that the screen is against the surface
and the cover is facing up.

4.

Remove the computer cover. See “Removing the computer cover” on page 83.

96

Hardware Maintenance Manual

Содержание ThinkCentre 0401











































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды