Lenovo ThinkAgile CP 4000 Series Скачать руководство пользователя страница 36

Страница: 36 / 84

Step 6. Secure the rear mounting bracket of the rail with two M5 screws.

Step 7. Extend the rail until the front mounting bracket of the rail reaches the front rack.

Step 8. Repeat steps Step 1

on page 27 through Step 5

on page 27 to install the front rail mounting

bracket to the front mounting flange.

Attention:

• For the front mounting bracket, the screws for square hole rack need to be fastened in the same

holes as the preinstalled screws for round hole rack. Otherwise, the storage enclosure cannot be
secured to the front mounting bracket.

• After fastening the two screws for square hole rack, do not further secure the front mounting

bracket of the rail with screws until you install the storage enclosure into the rack.

Step 9. Repeat steps Step 1

on page 27 through Step 8

on page 28 to install the opposite rail in the

rack.

The installation of the storage block slide rails in a square hole rack is now complete.

The next step is to install the storage enclosure: “Install the storage enclosure” on page 29

Lenovo ThinkAgile CP Hardware Installation Guide

Содержание ThinkAgile CP 4000 Series





















































































Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды

Lenovo ThinkAgile CP 4000 Series, Руководство по установке оборудования

Результаты поиска

Содержание ThinkAgile CP 4000 Series

Отзывы:

Похожие инструкции для ThinkAgile CP 4000 Series

Бренды по названию

Популярные бренды