Lenovo RackSwitch G7028 Скачать руководство пользователя страница 52

Страница: 52 / 86

G7028 Installation Guide

DANGER

Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil À Laser de Classe 1

To install an SFP optical transceiver in an SFP+ port slot on the switch, complete the

following steps.

Note:

To avoid damage to the cable or the SFP transceiver, do not connect the

cable before you install the transceiver.

1. Remove the safety cap and pull the locking lever into the down (unlocked)

position.

2. Insert the transceiver into the slot until it clicks into place. Use minimal pressure

when you insert the transceiver. Do not use excessive force when you insert

the transceiver or you might damage the transceiver or the slot.
The transceiver has a mechanical guide key to prevent you from inserting the
transceiver in an incorrect orientation.

3. Pull up the locking lever to lock the transceiver into place.
4. Connect the fiber-optic cable following the

“Cabling Guidelines” on page 34

To remove an SFP optical transceiver, disconnect the fiber-optic cable, and pull

down the locking lever to release the transceiver. After you remove the transceiver,

replace the safety cap.

Installing an SFP+ Optical Transceiver

Approved 10 GbE SFP+ optical transceivers are supported in G7028 SFP+ port

slots. The SFP+ optical transceiver provides two fiber-optic cable connectors for

connecting to external ports.

Some laser products contain an embedded Class 3A or Class 3B laser
diode. Note the following.

Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.

Содержание RackSwitch G7028























































































Результаты поиска

Содержание RackSwitch G7028

Отзывы:

Похожие инструкции для RackSwitch G7028

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7028, Руководство по установке

Результаты поиска

Содержание RackSwitch G7028

Отзывы:

Похожие инструкции для RackSwitch G7028

Бренды по названию

Популярные бренды