Lenovo RackSwitch G7028 Скачать руководство пользователя страница 21

Страница: 21 / 86

Chapter 2: Switch Components

RJ-45 Management Port

The RJ-45 management port on the front panel supports 10/100/1000BASE-T,

in-line switch management.

To attach an RJ-45 connector to the switch, push the RJ-45 cable connector into the

port connector until it clicks into place.

To disconnect the RJ-45 cable, squeeze the release tab and gently pull the cable

connector out of the switch connector.

RJ-45 Management LEDs

The RJ-45 management port LEDs are oriented as shown in the following figure.

Figure 5. RJ-45 management port LEDs

Status LEDs for the RJ-45 management port are described in the following table.

Reset Button

The Reset button is recessed within a hole on the front panel. Use a straightened

paper clip or similar object to press the Reset button. The Reset button allows

technicians to reset the switch as follows:
•

Normal reset—Press and release Reset. The switch resets and reloads the
configuration files.

•

Factory reset—Press and hold Reset for more than five seconds. The switch
resets and reverts all configuration settings to the factory defaults.

Table 2. RJ-45 status LEDs behavior

LED

State

Functional Meaning

Link/Activity

Steady green

Link up

Flashing green

Activity

Off

No link

Speed

Steady green

100/1000 Megabits per second (Mbps)

Off

10 Mbps or no link

Link/Activity LED

Speed LED

Содержание RackSwitch G7028























































































Результаты поиска

Содержание RackSwitch G7028

Отзывы:

Похожие инструкции для RackSwitch G7028

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7028, Руководство по установке

Результаты поиска

Содержание RackSwitch G7028

Отзывы:

Похожие инструкции для RackSwitch G7028

Бренды по названию

Популярные бренды