manualshive.com logo in svg

Lennox XC20-024-230-01, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lennox XC20-024-230-01 Скачать руководство пользователя страница 71

71

XC20

Intelligent Power Module

Converter

Heat Sink

Power Factor
Correction

Circuit

Communication Control

Figure 52. 4- and 5-Ton Unit Inverter

STATUS CODES:

Table 17. Outdoor Control 7-Segment Display Alert Codes and Inverter LED Flash Codes

NOTE - System fault and lockout codes take precedence over system status codes (cooling, heating operating percentages or defrost/de­
humidification). Only the latest active fault or lockout codes are displayed (if present). If no fault or lockout codes are active, then system
status codes are displayed. Alert codes are also displayed on the iComfort Wi-Fi

® 

or iComfort

®

 S30 thermostat.

Alert

Codes

Inverter LED Flash
Code (number of
flashes)

Priority

Alarm Description

Possible Causes and Clearing Alarm

Red LED

Green

LED

N/A

ON

OFF

N/A

XC 20-024 and -036 only: Indicates inverter is operating normally.

N/A

ON

ON

N/A

XC 20-048 and -060 only: Indicates inverter is operating normally.

N/A

OFF

OFF

N/A

Indicates inverter is NOT energized.

ERROR CODES

:

Table 18. Outdoor Control 7-Segment Display Alert Codes and Inverter LED Flash Codes

NOTE - System fault and lockout codes take precedence over system status codes (cooling, heating operating percentages or defrost/dehumidification).
Only the latest active fault or lockout codes are displayed (if present). If no fault or lockout codes are active, then system status codes are displayed. Alert
codes are also displayed on the iComfort Wi-Fi

® 

or iComfort

®

 S30 thermostat.

Alert

Codes

Inverter

Code

Inverter LED Flash
Code (number of
flashes)

Priority

Alarm Description

Possible Causes and Clearing Alarm

Red LED

Green LED

E 423

40

4 flashes

OFF

Moderate

/ Critical

The inverter has detected a
circuit problem

.

Control will lock out after 10 strikes within an hour. To
clear disconnect power to outdoor unit and restart.

E 426

N/A

N/A

N/A

Critical

Excessive inverter alarms

After ten faults within one hour, control will lock out.

Indicates poor system operation. Review history of
alarms to resolve system setup. Check condenser fan
motor, TXV, indoor unit blower motor, stuck reversing
valve, over-charge,  undercharge, and clogged refriger­
ant filter.

To clear error, disconnect power to outdoor unit and re­
start. Inverter alarms 12 to 14 and 53 do not count to­
wards this lock out condition.

Содержание XC20-024-230-01















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды