Lennox XC20-024-230-01 Скачать руководство пользователя | Manualshive

Страница: 66 / 78

background image

66

XC20

Outdoor Control Operation, Checkout and Status / Error Codes

OPERATION:

The outdoor control is a microprocessor-based device for use with variable-capacity compressors up to 5-tons in capacity
operating on 24VAC residential power. The outdoor control integrates the functionality of maintaining compressor speed,
demand, defrost and fan PWM controls. The outdoor control is self-configuring. During start-up the outdoor control selects
one of two configurations variable-capacity air conditioner or variable-capacity heat pump

.

PUSH

BUTTON

7-SEGMENT

DISPLAY

WHEN UNIT IS IN PUMP-DOWN MODE,

WILL BE DISPLAYED

ON 7-SEGMENT.

TO ACTIVATE PUMP-DOWN MODE, REFER TO PUMP-DOWN

CYCLE SEQUENCE ON PAGE 39.

NOTE - The green LED located on the outdoor control flashes when
communication occurs between the outdoor control and either the
thermostat or the inverter.

Figure 48. Outdoor Control Unit

STATUS CODES:

Table 13. Outdoor Control 7-Segment Display Alert Codes - Outdoor Control Status

NOTE - System fault and lockout codes take precedence over system status codes (cooling, heating operating percentages or defrost/dehumidification).

Only the latest active fault or lockout codes are displayed (if present). If no fault or lockout codes are active, then system status codes are displayed. Alert

codes are also displayed on the iComfort Wi-Fi

®

or iComfort

®

S30 thermostat.

Alert Codes

Priority

Alarm Description

Possible Causes and Clearing Alarm

E 600

Critical

Compressor has
been cycled OFF on
utility load shedding.

Load shedding function: Provides a method for a local utility company to limit the maximum power
level usage of the outdoor unit. The feature is activated by applying 24 volts AC power to the L and C
terminals on the outdoor control.

E 601

Critical

Outdoor unit has
been cycled OFF on
low temperature
protection.

Low temperature Protection: Outdoor unit will not operate when the outdoor temperature is at or
below 4°F (20°C). If the unit is operating and the outdoor temperature drops below 4°F (20°C),
the unit will continue to operate until the room thermostat is satisfied or the outdoor temperature
drops to 15°F (26°C). (Outdoor unit ambient sensor provides temperature readings.)

«
...
64
65
66
67
68
...
»

Содержание XC20-024-230-01















































































Отзывы:

Нет отзывов

Похожие инструкции для XC20-024-230-01

Бренд: Ideal Air Страницы: 28

iCongo PSQ-08-01

Бренд: Soleus Air Страницы: 18

VRV III BSVQ100P8V1B

Бренд: Daikin Страницы: 20

MissionCritical MC-2x2

Бренд: AboveAir Technologies Страницы: 24

Бренд: Danby Страницы: 40

X-Power VRF series

Бренд: Carrier Страницы: 11

bycool green line LITE

Бренд: dirna Bergstrom Страницы: 64

Бренд: Olimpia splendid Страницы: 108

Бренд: Danby Страницы: 56

Бренд: Haier Страницы: 36

Бренд: Haier Страницы: 14

Бренд: Samsung Страницы: 99

Бренд: Samsung Страницы: 112

Бренд: Samsung Страницы: 150

Бренд: Samsung Страницы: 95

Бренд: Brezza Страницы: 40

Бренд: GEAppliances Страницы: 48

Бренд: GEAppliances Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды