manualshive.com logo in svg

Lennox XC20-024-230-01, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lennox XC20-024-230-01 Скачать руководство пользователя страница 35

35

XC20

Table 6. Outdoor Control 7-Segment Display Alert Codes and Inverter LED Flash Codes

NOTE - System fault and lockout codes take precedence over system status codes (cooling, heating operating percentages or defrost/dehumidification).
Only the latest active fault or lockout codes are displayed (if present). If no fault or lockout codes are active, then system status codes are displayed. Alert
codes are also displayed on the iComfort Wi-Fi

® 

thermostat.

Alert

Codes

Inverter

Code

Inverter LED Flash

Code (number of

flashes)

Priority

Alarm Description

Possible Causes and Clearing Alarm

Red LED

Green LED

E 441

14

1 flash

4 flashes

Moderate

Compressor slowdown due
to high compressor current.
Compressor current is ap­
proaching limit. The com­
pressor speed automatic­
ally slows. The control sets
indoor CFM and outdoor
RPM to values according to
demand percentage rather
than the actual Hz. Alarm is
automatically cleared..

Issue

: Possible issue is system running at high pres­

sures. Check for high pressure trips or other alert codes in
room thermostat and outdoor control.

E 442

N/A

N/A

N/A

Critical

The top cap switch has
opened five times within
one hour. As a result, the
outdoor unit is locked out

.

When compressor thermal protection sensor opens five
times within one hour, outdoor stops working. To clear,
disconnect power to outdoor unit and restart.

E 443

N/A

N/A

N/A

Critical

Incorrect appliance unit
size code selected.

Check for proper configuring of unit size codes for out­
door unit in configuration guide or in installation instruc­
tions. If replacing inverter, verify inverter model matches
unit size. The alarm/fault clears after the correct match is
detected following a reset. Remove the thermostat from
the system while applying power and reprogramming.

E 600

N/A

N/A

N/A

Critical

Compressor has been
cycled OFF on utility load
shedding.

Load shedding function: Provides a method for a local
utility company to limit the maximum power level usage of
the outdoor unit. The feature is activated by applying 24
volts AC power to the L and C terminals on the outdoor
control.

E 601

N/A

N/A

N/A

Critical

Outdoor unit has been
cycled OFF on low temper­
ature protection.

Low temperature protection: Outdoor unit will not operate
when the outdoor temperature is at or below  ­4°F
(­20°C).  If the unit is operating and  the outdoor temper­
ature drops below ­4°F (­20°C), the unit continues to op­
erate until the room thermostat is satisfied or the outdoor
temperature drops to ­15°F (­26°C).  Outdoor unit ambi­
ent sensor provides temperature readings.

Содержание XC20-024-230-01















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды