Lennox T?CLASS TPA S4, Информационное руководство

Страница: 16 / 18

Page 16
Revised 05−2009 TPA*S4
Table 11. TPA048S4N43Y
INDOOR MATCHUPS
Target
Subcooling
Heat Cool
*Add
charge
g
Heat Cool
(+5ºF)(+1ºF)
lb oz
CBX26UH−048 9 11 1 7
CBX26UH−060 24 18 2 7
CBX27UH−048−230 11 11 1 3
CBX27UH−060−230 24 18 2 7
CBX32M−048 11 11 1 3
CBX32M−060 11 11 1 3
CBX32MV−048 11 11 1 3
CBX32MV−060−230 11 11 1 3
CBX40UHV−048 11 11 1 3
CBX40UHV−060 11 11 1 3
CH33−43C 18 7 0 0
CH33−49C, −50/60C 11 11 1 3
CH33−60D 11 11 0 9
CH33−62D 11 11 1 10
CR33−50/60 25 7 0 9
CR33−60 25 7 0 9
CX34−49 11 11 1 1
CX34−60D 11 11 0 9
Table 12. TPA060S4N43Y
INDOOR MATCHUPS
Target
Subcooling
Heat Cool
*Add
charge
g
Heat Cool
(+5ºF)(+1ºF)
lb oz
CBX26UH−060 10 11 1 7
CBX27UH−060−230 10 9 0 13
CBX32MV−060 10 9 0 0
CBX32MV−068 10 9 0 9
CBX40UHV−060 10 9 0 0
CH33−60D 10 9 0 0
CH33−62D 10 9 0 11
CX34−62D 10 9 0 6
*Amount of charge required in additional to charge shown on unit
nameplate. (Remember to consider line set length difference.)
Table 13. HFC−410A Temp. (°F) − Pressure (Psig)
°F Psig °F Psig °F Psig °F Psig
−40 10.1 21 80.5 56 158.2 91 278.2
−35 13.5 22 82.3 57 161 92 282.3
−30 17.2 23 84.1 58 163.9 93 286.5
−25 21.4 24 85.9 59 166.7
94 290.8
−20 25.9 25 87.8 60 169.6 95 295.1
−18 27.8 26 89.7 61 172.6 96 299.4
−16 29.7 27 91.6 62 175.4 97 303.8
−14 31.8 28 93.5
63 178.5
98 308.2
−12 33.9 29 95.5 64 181.6 99 312.7
−10 36.1 30 97.5 65 184.3 100 317.2
−8 38.4 31 99.5 66 187.7 101 321.8
−6 40.7
32 100.8
67 190.9 102 326.4
−4 43.1 33 102.9 68 194.1 103 331
−2 45.6 34 105 69 197.3 104 335.7
0 48.2 35 107.1 70 200.6 105 340.5
1 49.5
36 109.2 71 203.9 106 345.3
2 50.9 37 111.4 72 207.2 107 350.1
3 52.2 38 113.6 73 210.6 108 355
4 53.6 39 115.8 74 214 109 360
5 55 40 118 75 217.4 110 365
6 56.4 41 120.3 76 220.9 111 370
7 57.9 42 122.6 77 224.4 112 375.1
8 59.3 43 125 78 228 113 380.2
9 60.8 44 127.3 79 231.6 114 385.4
10 62.3 45 129.7 80 235.3 115 390.7
11 63.9 46 132.2 81 239 116 396
12 65.4 47 134.6 82 242.7 117 401.3
13 67 48 137.1 83 246.5 118 406.7
14 68.6 49 139.6 84 250.3 119 412.2
15 70.2 50 142.2 85 254.1 120 417.7
16 71.9 51 144.8 86 258 121 423.2
17 73.5 52 147.4 87 262 122 428.8
18 75.2 53 150.1 88 266 123 434.5
19 77 54 152.8 89 270 124 440.2
20 78.7 55 155.5 90 274.1
125 445.9
IV − MAINTENANCE
At the beginning of each heating or cooling season, the
system should be cleaned as follows:
A − Outdoor Unit
1 − Clean and inspect condenser coil. (Coil may be
flushed with a water hose).
NOTE − Make sure all power is disconnected before
flushing coil with water.
2 − Visually inspect all connecting lines, joints and
coils for evidence of oil leaks.
NOTE-Outdoor fan motors are permanently
lubricated.
B − Indoor Coil
1 − Clean coil if necessary.
2 − Check connecting lines and coil for evidence of oil
leaks.
3 − Check condensate line and clean if necessary.
C − Indoor Unit
1 − Clean or change filters.
2 − Bearings are pre-lubricated and need no further
oiling.
3 − Check all wiring for loose connections.
4 − Check for correct voltage at unit.
5 − Check amp−draw on blower motor.