Lennox SCU14M Series Скачать руководство пользователя страница 1

# 504,465M

Page 1

Save these instructions for future reference

INSTALLATION AND MAINTENANCE

INSTRUCTIONS

SCU14M Series

Split System Air Conditioner

TABLE OF CONTENTS

UNIT DIMENSIONS ............................... 2

INSTALLATION ...................................... 3

START-UP ............................................ 10

OPERATION ........................................ 12

MAINTENANCE ................................... 12

CONNECTION DIAGRAM ................... 14

WARRANTY ......................................... 15

Sharp metal edges can cause injury. When
installing the unit, use care to avoid sharp
edges.

  WARNING

Installation and servicing of air conditioning
equipment can be hazardous due to internal
refrigerant pressure and live electrical com-
ponents. Only trained and qualified service
personnel should install or service this equip-
ment. Installation and service performed by
unqualified persons can result in property
damage, personal injury, or death.

  WARNING

Risk of electrical shock. Disconnect all
remote power supplies before installing or
servicing any portion of the system. Failure
to disconnect power supplies can result in
property damage, personal injury, or death.

  WARNING

The equipment covered in this manual is to be installed by trained and experienced
service and installation technicians. Improper installation, modification, service, or
use can cause electrical shock, fire, explosion, or other conditions which may cause
personal injury, death, or property damage. Use appropriate safety gear including
safety glasses and gloves when installing this equipment.

 

WARNING

Manufactured By

A.A.C.

A Lennox International Company

421 Monroe Street

Bellevue, OH 44811

Содержание SCU14M Series
















Отзывы: