LENNOX HEARTH PRODUCTS • MONTEBELLO
®
DLX POWER VENT DV GAS FIREPLACES (MDLX40/45IN-PV) • CARE AND OPERATION INSTRUCTIONS
13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
WARNING
Any safety screen or guard
removed for servicing the
appliance must be replaced
prior to operating the
appliance.
AVERTISSEMENT
Tout écran ou protecteur retiré
pour permettre l’entretien
de l’appareil doit être remis
en place avant de mettre
l’appareil en marche.
WARNING
Do not operate appliance with
the glass front removed, cracked
or broken.
Front Glass Enclosure Panel Removal
and Installation
To install the front glass door assembly,
proceed as follows:
1. Retrieve the glass door assembly. Visually
inspect the gasket on the backside of the
panel. The gasket surface must be clean,
free of irregularities and seated firmly.
2. Position the door frame in front of the
firebox opening and engage the bottom
flange over the rail at the bottom of the
firebox opening.
3. Swing the door up and back. Ensure the
gasket seats evenly as the door draws
shut. Engage the nut insert and fasten with
two screws to secure the door.
4. Install the door modesty shield on top
flange glass door as follows: grab the door
modesty shield with both hands, with the
open hem going down and engage it with
the upper lip of the glass door frame by
pushing it all the way down. Make sure the
installed shield is firmly in place.
5. With the firescreen hanging on the screen
rod, drop in the right side of the rod to the
right modesty panel. Then drop in the left
side of the rod through the slot of the left
modesty panel. Make sure that the rod is
supported by the bracket in the center of
the fireplace.
WHEN INSTALLING THE GLASS DOOR,
SECURELY TIGHTEN THE LATCH
SCREWS—SEE THE FIRST WARNING
ON THIS PAGE.
When installing the glass door, ensure
the spacing on both sides are equal.
Figure 9: Front Glass
Enclosure Panel
Top Flange Glass Door
Frame Assembly
Glass Door Latch (2)
Latch
Screws
Firebox Floor
Glass Door Assembly
WARNING
•
When reinstalling the glass
door, the door latch screws
must be securely tightened
to prevent the glass door
from falling out, which could
potentially cause damage
and possible injury.
•
Do not attempt to substitute
the materials used on this
door, or replace cracked or
broken glass.
•
Handle this glass with
extreme care! Glass is
susceptible to damage—Do
not scratch or handle roughly
while reinstalling the glass
door frame.
•
The glass door of this
appliance must only be
replaced as a complete
unit as provided by the
manufacturer. Do not attempt
to replace broken, cracked or
chipped glass separately.
•
Do not attempt to touch
the front enclosure glass
with your hands while the
fireplace is in use.
AVERTISSEMENT
Ne pas utiliser l'appareil si le
panneau frontal en verre n'est
pas en place, est craqué ou
brisé.
Only doors certified with the appliance
shall be used.
Seules des portes certifiées pour cet
appareil doivent être utilisées.
WARNING: DO NOT abuse glass door
by striking or slamming shut.
These are direct-vent appliances. They are
designed to operate only when the front glass
enclosure panel is installed. Generally the front
glass enclosure panel should not be removed
except to gain access to the components
within the firebox.
Removing Glass Enclosure Panel
(see
Figure 9)
To remove the firescreens, lift up the center
of the rod to disengage it from the center
bracket, bend down at center, hold left side
with hand until it disengages from left side,
being careful not to scratch paint. Slowly
remove the rod from the right side.
Remove the door modesty shield from the
top flange glass door by pulling it up firmly
with both hands until it is disengaged. Using
a phillips screwdriver, unfasten two (2)
screws located at the top of the glass frame.
Tilt the glass frame at the top away from the
unit. Lift it carefully off the bottom door track
and set the door aside, protecting it from
inadvertent damage.
