Lennox Merit Plus MPD35PF-NE-B Скачать руководство пользователя страница 36

Страница: 36 / 40

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

GAS CONVERSION KITS

Natural Gas to Propane Gas

Conversion Kits

Fireplace

Model No.

Cat. No.

(model)

MPD35ST/PF-NM

millivolt

H3360

(GCK35STMPN)

MPD35ST/PF-NE

electronic

H336

(GCK35STENP)

Table 12

Propane Gas to Natural Gas

Conversion Kits

Fireplace

Model No.

Cat. No.

(model)

MPD35ST/PF-PM

millivolt

H204

GCK-MPD40MPN

MPD35ST/PF-PE

electronic

26M65

(GCK-MP40EPN)

Table 13

Gas conversion kits are available to adapt the

appliance from the use of one type of gas to

the use of another. These kits contain all the

necessary components needed to complete the

task including labeling that must be affixed to

ensure safe operation.

Kit part numbers are listed here and the following

steps detail the conversion procedure.

Step . Turn off the gas supply to the appliance.

a. Open the control compartment access

panel, by actuating the spring-loaded

magnetic catches securing the panel,

gently depressing the outer top corners

of the panel until the catches "pop" the

panel free and allowing it to swing out

and down to open.

b. Remove the bottom control compart-

ment access panel by compressing the

spring-loaded hinge pin on the left side

until it disengages from the left cabinet

panel hole. Pull the panel away from the

fireplace. See

Figure 49

Page 27

IMPORTANT - CANADA ONLY:

The conversion shall be car-

ried out in accordance with the

requirements of the provincial

authorities having jurisdiction

and in accordance with the

requirements of the CAN-

B49. And B49.2 Installation

code.

WARNING: This conversion kit

shall be installed by a quali-

fied service agency in accor-

dance with the manufacturer's

instructions and all applicable

codes and requirements of the

authorized having jurisdiction. If

the information in these instruc-

tions is not followed exactly, a

fire, explosion or production of

carbon monoxide may result

causing property damage, per-

sonal injury or loss of life. The

installation is not proper and

complete until the operation

of the converted appliance is

checked as specified in the owner

instructions supplied with the

kit. The qualified service agency

performing this installation

assumes responsibility for this

conversion.

ATTENTION - LE CANADA SEULE-

MENT: La conversion devra être

effectuée conformément aux

recommandations des autorités

provinciales ayant juridiction et

conformément aux exigences

du code d'installation CAN-

B49. Et.2.

AVERTISSEMENT: Cet Équipement

de conversion sera installÉ par une

agence qualifiÉe de service confor-

mÉment aux instructions du fabri-

cant et toutes exigences et codes

applicables de l’autorisÉs avoir la

juridiction. Si l’information dans

cette Instruction n’est pas suivie

exactement, un feu, explosion ou

production de protoxyde de car-

bone peut rÉsulter le dommages

causer de propriÉtÉ, perte ou bles-

sure personnelle de vie. L’agence

qualifiÉe de service est espon-

sable de l’installation propre de

cet Équipment. L’installation n’est

pas propre et complÉte jusqu’à

l’opÉration de l’appareil converti

est chÉque suivant les critères

Établis dans les instructions de

propriÉtaire provisionnÉes avec

l’Équipement.

Содержание Merit Plus MPD35PF-NE-B









































Результаты поиска

Содержание Merit Plus MPD35PF-NE-B

Отзывы:

Похожие инструкции для Merit Plus MPD35PF-NE-B

Бренды по названию

Популярные бренды

Lennox Merit Plus MPD35PF-NE-B, Руководство по установке

Результаты поиска

Содержание Merit Plus MPD35PF-NE-B

Отзывы:

Похожие инструкции для Merit Plus MPD35PF-NE-B

Бренды по названию

Популярные бренды