Lennox iHarmony Zone Thermostat Скачать руководство пользователя страница 5

Страница: 5 / 16

Trim 1/4 inch (6 mm) insulation from end of each

thermostat wire lead.

Use the provided wall plate as a template on

where to drill the mounting holes.

NOTE:

Installation of wall plate is optional. Use

a field-provided level to allow for proper

alignment.

(Use a level) Align Wall Plate

Use unit wall plate as template to mark desired

mounting hole locations on wall.

Drill 3/16” (5 mm) holes in wall for provided wall

anchors. Insert provided wall anchors into drilled

holes.

Remove back plate from main zone sensor

assembly using a flat-head screw driver.

Route wiring from wall through center openings

on wall plate (use is optional) and back plate.

Wall Plate (optional)

Zone Sensor Back Plate

Run thermostat wire

through openings

Содержание iHarmony Zone Thermostat

















Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды

Lennox iHarmony Zone Thermostat, Инструкция по установке и настройке

Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды