Lennox iHarmony Zone Thermostat Скачать руководство пользователя страница 8

Страница: 8 / 16

address using the plus/minus buttons. Selections

are 2, 3 or 4.

NOTE:

Zone 1 is always the S30 thermostat. Each

additional zone sensor will have to have a

unique zone number assigned to it.

zone number

zone

Figure 4. Zone Selection

Menu > Advanced Settings

This represents the menu icon. Most

procedures will start with menu and with

directions to sub-menus.

Table 3 lists the settings that can be adjusted under

this menu selection

Table 3. Advanced Settings

Menu Selection Setting

Zone

Number

Default value is 2. Minimum value is

2. Maximum value is 4. Adjustment is

made with using the + or - selection

tool.

NOTE:

Zone 1 is always reserved for

the S30.

Table 3. Advanced Settings

Menu Selection Setting

Reset

Resets the zone sensor to factory

default settings. Select Confirm to

reset all.

Restart

Reboots the zone sensor.

Содержание iHarmony Zone Thermostat

















Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды

Lennox iHarmony Zone Thermostat, Инструкция по установке и настройке

Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды