Lennox iHarmony Zone Thermostat Скачать руководство пользователя страница 3

Страница: 3 / 16

CAUTION

This is a 12VDC low-voltage zone sensor. Do not

install on voltages higher than 14VDC.

Electrical Characteristics

All values are at 77°F (25°C). This unit does employ

mis-wire circuit protection.

Table 1. Zone Sensor Power Requirements

Min

Nom

Max

Unit

Input

Voltage

VDC

Input

Current

61.5

133

WARNING

Always turn off power at the main power source

by switching the circuit breaker to the OFF

position before installing or removing this zone

sensor.
All wiring must conform to local and national

building and electrical codes and ordinances.

Dimensions

Unit Dimensions (H x W x D)

Dimensions: 3-5/16 x 4-5/16 x 7/8 in. (84 x 110 x

22mm)

Wall Plate Dimensions (H x W)

Dimensions: 4-1/2” x 5-3/4” (114 x 146mm)

Installation Guide

Installation Considerations

The 17A30 zone sensor is a 12VDC low-voltage

device and requires a common wire to the damper

control module to operate.

•

Shut off all power to system components before

installing zone sensor.

• Make sure that all wiring conforms to local

and national building and electrical codes and

ordinances.

• Never install the zone sensor on outside walls or

in direct sunlight.

• Use 2-pair, 18AWG unshielded thermostat cable

(field-provided) for power terminals (PWR and

C). Recommend using 2-pair 22AWG shielded

thermostat cable for communications terminals

(D+ and D-) which will help eliminate any noise

interference.

Содержание iHarmony Zone Thermostat

















Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды

Lennox iHarmony Zone Thermostat, Инструкция по установке и настройке

Результаты поиска

Содержание iHarmony Zone Thermostat

Отзывы:

Похожие инструкции для iHarmony Zone Thermostat

Бренды по названию

Популярные бренды