Lennox G24M SERIES Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 36

Lennox G24M SERIES Скачать руководство пользователя страница 33

3DJH

PROBLEM 3: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER DOES

NOT ENERGIZE (CONT.).

Condition

Possible Cause

Corrective Action/Comments

3.3

-- Unit operates with a cooling and

continuous fan demand.

-- Combustion air blower will not

start with a Heating demand.

-- Diagnostic lights flash the pres-

sure switch failure code 2.5 minutes

3.3.1

Miswiring of furnace or improper

connections to combustion air

blower.

ACTION 1 -- Check for correct wiring and

loose connections. Correct wiring and/or re-

place any loose connections.

sure switch failure code 2.5 minutes

after heating demand.

LED#1--Off,

LED#2--Slow Flash

3.3.2

Combustion air blower failure.

ACTION 1 -- If there is 120V to combustion air

blower and it does not operate, replace com-

bustion air blower.

PROBLEM 4: UNIT FAILS TO FIRE IN THE HEATING MODE, COMBUSTION AIR BLOWER

ENERGIZES, IGNITOR IS NOT ENERGIZED.

Condition

Possible Cause

Corrective Action/Comments

4.1

-- Unit operates with a cooling and

continuous fan demand.

-- Combustion air blower ener-

gizes with a heating demand

4.1.1

Pressure switch does not close

due to incorrect routing of the

pressure switch lines.

ACTION 1 -- Check that the pressure switch

lines are correctly routed. Correctly route

pressure switch lines.

gizes with a heating demand.

-- Diagnostic lights flash the pres-

sure switch failure code 2.5 min-

utes after heating demand.

4.1.2

Pressure switch does not close

due to obstructions in the pressure

lines.

ACTION 1 -- Remove any obstructions from

the the pressure lines and/or taps.

LED#1--Off

LED#2--Slow Flash

4.1.3

Pressure switch lines damaged

ACTION 1 -- Check pressure switch lines for

leaks. Replace any broken lines.

LED#2 Slow Flash

4.1.4

Pressure switch does not close

due to a low differential pressure

across the pressure switch.

ACTION 1 -- Check the differential pressure
across the pressure switch. This pressure
should exceed the set point listed on the
switch.
ACTION 2 -- Check for restricted inlet and
exhaust vent. Remove all blockage.
ACTION 3 -- Check for proper vent sizing
and run length. See installation instruc-
tions.
ACTION 4 -- Check voltage to thre combus-
tion air blower.

4.1.5

Wrong pressure switch installed in

the unit, or pressure switch is out

of calibration.

ACTION 1 -- Check that the proper pressure

switch is installed in the unit. Replace pres-

sure switch if necessary.

4.1.6

Miswiring of furnace or improper

connections at pressure switch.

ACTION 1 -- Check for correct wiring and

loose connections. Correct wiring and/or re-

place any loose connections.

4.1.7

Pressure switch failure.

ACTION 1 -- If all the above modes of failure

have been checked, the pressure switch may

have failed. Replace pressure switch and de-

termine if unit will operate.

«
...
31
32
33
34
35
...
»

Содержание G24M SERIES





































Отзывы:

Нет отзывов